ORG Clean MC 103 (Membrane Cleaner) Manufacturer, Exporter, Distributor, Supplier in MUMBAI, MAHARASHTRA.

MUMBAI CHEMICAL is leading one Largest Supplier, Manufacturer and Exporter of ORG Clean MC 103 (Membrane Cleaner) in Maharashtra, Mumbai, Thane, Navi Mumbai, Panvel, Raigad, Chiplun, Ratnagiri, Kudal, Kolhapur, Sangli, Karad, Satara, Pune, Nashik, Sambhaji Nagar, Ahmadnagar, Palghar, Tarapur( Boiser) , Dhule, Nandurbar, Jalgaon, Kurkumbh (Daund), Osmanabad, Latur, Nanded , Buldhana, Amaravati, Vashim, Akola, Nagpur, Vardha, Yavatmal, Chandrapur, Bhandara, Gadchiroli.

Product Information:
ORG Clean MC 103 (Membrane Cleaner) : RXSOL-33-3322-025
ORG Clean MC 103 (Membrane Cleaner) is a low pH, liquid formulation designed specifically to remove metal hydroxides, calcium carbonate, and other similiar scales from Reverse osmosis (RO), nanofiltration (NF), microfiltration (MF) and ultrafiltration (UF) membranes. This highly effective product provides superior cleaning resulting in longer system running time.
Acidic powerfull cleaner, non-foaming (pH1.6).

Product Application:

Suitable for use wtih all thin film or cellulosic membranes.
Buffered to maintain an effective pH over a range of dilutions.
Cleaner for ease of mixing.
No adverse effects with repeated use.
Enhanced performance at elevated temperature.
Low foam formulation.

Using Procedure:
TYPICAL APPLICATIONS
During the operation of a membrane separation system, dissolved solids in the incoming water can concentrate up to a level where they begin to precipitate on the membrane surface. Scaling from hardness and metal salts found in most unsoftened water supplies impedes the flow of water through the membrane. This can result in unacceptably low production, high operating pressure, or an excessive pressure drop in the system, which may lead to irreversible membrane damage. Additionally, the accumulation of scale next to the membrane surface can increase the amount of dissolved material passing through the membrane, resulting in product water of unacceptable quality. Before the scale accumulates to a level where product water declines, or membrane damage can occur, it should be removed through clean-in-place (CIP), off-line cleaning. Indications of the need for cleaning include a significant decrease in normalized permeate flow, a significant increase in pressure drop across the system (or individual stage), or an increase in the normalized salt passage, so that product quality is unacceptable.
ORG Clean MC 103 (Membrane Cleaner)  contains a blend of solubilizing and complexing agents designed to specifically remove calcium carbonate and metal hydroxide-based scales from the surfaces of a membrane. Used in tandem with an alkaline cleaner for organics and particulate removal, regular cleanings with ORG Clean MC 103 (Membrane Cleaner) helps to preserve the life of your membranes. Depending on the nature of the fouling, a soak period may be necessary for optimum results.

GENERAL CLEANING INSTRUCTIONS
The following general cleaning procedure can be followed.
Inspect cleaning tank, hoses, and cartridge filters. Clean tank and flush hoses if necessary. Install new cartridge filters.
Fill cleaning tank with RO permeate or DI water. Turn on agitator or tank recirculation pump.
Slowly add ORG Clean MC 103 (Membrane Cleaner)  to cleaning tank (1 gal [3.8 L] of product for every 50 gal [189 L] of water) and allow to mix thoroughly.
Check solution temperature. If solution temperature is lower than recommended level, adjust heating control to provide optimum temperature. If manufacturer%u2019s recommendation is not available, contact your RX MARINE representative.
Check solution pH. The solution pH should be 2.5-3.5 or as recommended by the membrane manufacturer. If pH is too low, adjust pH upwards with NaOH, or other chemical as recommended by the membrane manufacturer. If pH is too high, adjust with hydrochloric acid.
Circulate solution through one stage at a time in the direction of feed flow for 30 minutes. Circulate at the flow rate recommended by the
membrane or system manufacturer. If manufacturer%u2019s recommendation is not available, contact your Betz Dearborn representative. Pressure
should be low enough so that no permeate is produced during cleaning, but always less than 60 psig (4.2 kg/cm2). In cases of heavy fouling, the first return flow (up to 15% of the cleaning tank volume) should be diverted to drain to prevent redeposition of removed solids. For optimum results, each stage must be cleaned separately in a multistage system.
If the first stage cleaning solution becomes turbid or discolored, dump the tank and prepare a fresh cleaning solution before proceeding. If solution pH or temperature moves out of the recommended range, a new solution should be prepared. In any event, a new cleaning solution should be prepared for each stage.
Rinse with RO permeate at 20°C (68°F) minimum before returning system to service.
When returning unit to service, divert product water to drain until any residual cleaning solution has been rinsed from system.

SAFETY PRECAUTIONS
A Material Safety Data Sheet containing detailed information about this product is available upon request.

Product Note:

Product Technical Specification:

Available Packing Size: 10, 25, 50 Kg.

MUMBAI CHEMICAL offers highest quality products in Tank cleaning, Drilling Fluid Chemicals, Hold Solution, Agriculture, Lab Chemicals, Raw Chemicals, Sewage Chemicals, Detergent, Degreaser & Floor care chemical. Our in house lab and QC department is strong in equipment, knowledge and system to meet the international standards. We produce a superior range of ORG Clean MC 103 (Membrane Cleaner) with advanced manufacturing technology and using superior quality raw materials. We assure quality and ensure that only the best is catered to the customers. Our basic motto of the company is to give a better product to the customer at the lowest rate. We are keeping a ready stock of ORG Clean MC 103 (Membrane Cleaner) for more information, any support and price, Feel free to contact us through our Email id mumbaichems @ gmail.com

We are presently operative in all over India and you can buy our products from various location Like Andhra Pradesh, Tamil nadu, Gujarat , West Bengal  and also all seaports of India. We do have many satisfied customers in this Industries because of our QUALITY, PRICING & SERVICE. Our Company is also a Major Exporter & Mfg of ORG Clean MC 103 (Membrane Cleaner) in UAE, Oman , Vietnam, Europe, Africa, Bahrain, Qatar, Africa & many more countries.

Supply Locations :
Maharashtra , Mumbai, Thane, Navi Mumbai, Panvel, Raigad, Chiplun, Ratnagiri, Kudal, Kolhapur, Sangli, Karad, Satara, Pune, Nashik, Sambhaji Nagar, Ahmadnagar, Palghar, Tarapur( Boiser) , Dhule, Nandurbar, Jalgaon, Kurkumbh (Daund), Osmanabad, Latur, Nanded , Buldhana, Amaravati, Vashim, Akola, Nagpur, Vardha, Yavatmal, Chandrapur, Bhandara, Gadchiroli, All over Maharashtra.