Klin Kot is one of the original, environmental friendly water-based release products for the Marine, Shipping, Cement, Enginnering and construction industry. It has many applications in the industry including cleaning, asphalt, concrete, mining and hauling and is the ONLY fully adjustable water-based release on the market today with the ability to adjust from 1 to 1 thru 75 to 1, depending upon your application. KLIN KOT is an industry leader, having stood the test of time and proving to be an innovative and quality product for all facets of the industry.
These are the primary applications and suggested mix ratios for KLIN KOT . The ratios can be varied up or down according to your results. You can visit us on the web to view and print instruction sheets that are specific to your application. If you have any questions regarding a particular application or mix ratio.
Agricultural Equipment 8 to 1 - 10 to 1
Apply to keep mud and other debris from sticking to all farm equipment.
All Equipment 8 to 1
Use to inhibit rust and to keep equipment looking new. There is no build-up with KLIN KOT . Re-spray equipment after every wash.
Asphalt Equipment, Pavers & Trucks 8 to 1 - 11 to 1
Use KLIN KOT to keep asphalt from sticking to tools, equipment and trucks. Be sure to clean off all of the diesel, soap or other release agents before using KLIN KOT and remember to apply the product every time. It can also be used in the water tanks of rollers at 50 to 1. This will reduce the amount of water needed to prevent stickage and will also leave a coating on the drum allowing the operator to get off the pavement if the water should run out.
Boring and Tunneling Equipment 8 to 1 - 11 to 1
Use KLIN KOT to prevent mud and clay from sticking to conveyor belts, skid steer loaders, cranes, etc. At the end of the day, the mud and clay will clean right off of protected equipment. For the conveyor belts, a constant mist will keep it stick free and stop the hours of clean up at the end of the day.
Concrete Equipment 11 to 1
Spray all of your concrete finishing and placing equipment prior to every pour and clean up will be easy.
Concrete Forms 11 to 1 - 15 t o 1
KLIN KOT is safe for use on all form types including wood, aluminum and plastic. Be sure to clean or cast off as much of the old release as possible to eliminate any reaction between KLIN KOT and the old form release. Do NOT switch back and forth between KLIN KOT and other release agents. If the forms are new, season them just as you would with oil. The mix ratios vary from 15 to 1 for porous surfaces thru 11 to 1 for non-porous surfaces.
Concrete Form Liners 15 t o 1
KLIN KOT will provide a smooth, easy release to reproduce the liner design down to the finest detail. Call for vibration suggestions. The
typical mix ratio is 15 to 1 but can be varied depending upon results.
Concrete Pumping and Belt Trucks 11 to 1
Spray KLIN KOT on once per job and do not clean the hopper until the end of the job. Spray your entire truck. To polish truck, see "KLIN KOT Vehicle Instructions".
Construction Equipment 11 to 1
Apply to all equipment to keep mud and other debris from sticking to your equipment.
Hand Tools 11 to 1
Spray on hand tools regularly to inhibit rust and to keep them looking like new.
Liquid Mask 11 to 1
Spray KLIN KOT on any surface that is near where fresh concrete will be poured. KLIN KOT will not stain the surface and splatters can simply be brushed or power washed off.
Painting Equipment 10 to 1
Spray on all equipment to keep paint splatters from sticking to equipment, lifts and scaffolding. It also helps to keep the joints lubricated.Precast Concrete Industry Varies Please call for specialized assistance due to the many variables in the precast industry. Our specialitists will assist you in attaining the finish you are trying to achieve. Generally, the mix ratios vary from 11 to 1 thru 18 to 1.
Printing Industry 8 to 1
Use as a release of water based inks and glues in printing presses instead of grease.
Ready-Mix Trucks 11 to 1
Spray the entire truck with KLIN KOT as needed or after every wash. KLIN KOT will only need to be applied to the chute and hopper after every delivery. For cab polishing instructions please see "KLIN KOT Vehicle Instructions". Additional directions are available if needed.
Rental Equipment 11 to 1
Use to inhibit rust on equipment that is stored outside. It will also keep most paints from sticking to scissor lifts, etc. It will also keep asphalt, concrete and mud from sticking to your rental equipment.
Sawing and Planing Equipment 11 t o 1 - 50 to 1
Use in the tanks of saws and planers to reduce the amount of water needed to lubricate and cool the blades. KLIN KOT will also help reduce clean up time by preventing slurry from sticking to machines.
Snow Removal and Hauling Equipment 8 to 1
Use KLIN KOT to keep snow and ice from sticking to equipment. It can also be used as an environmentally safe way to keep snow from sticking inside dump truck boxes when hauling snow off-site. It also provides rust inhibiting qualities to protect from salt corrosion.
Tilt Up Concrete 11 to 1
Please call for specialized assistance due to the many variables regarding tilt up concrete projects. Our specialitists will assist you with proper mix ratios and application techniques. Instruction sheets are available.
Trucks, Buses, Trains, Etc... 11 to 1
KLIN KOT will help brighten faded equipment. It will also help prevent stains around the fueling inlets and exhaust stains on the vehicle's paint finish.
Vehicle Protectant and Polish 15 to 1
To apply KLIN KOT for the first time you must first wash the vehicle. Then spray on one panel at a time and polish in while droplets are still white. HINT: Mist on the front of the vehicle and let product go clear to help prevent bugs from sticking. KLIN KOT will also safely help remove bugs from your paint finish.
• Instructions for Using KLIN KOT on Concrete Forms
o Mix Ratio 11 to 1 -- For Porous Surfaces
o Mix Ratio 15 to 1 -- For Non-Porous Surfaces
o KLIN KOT gives you the ability to adjust your release agent to work best with the concrete mix design and type of forms that you are using. It is also safe for use on all form types including wood, aluminum and plastic.
Tips for Use
- Based upon your results, you may adjust the ratio by adding more or less concentrate. The more concentrate that is added, the more reactive it will be. The less concentrate that is added, the less reactive it will be. Reducing the amount of concentrate will reduce the amount of dusting, if any, left behind.
- For best results, remove as much of the previous form release as possible to eliminate any adverse reaction between KLIN KOT and the former release agent.
- If your forms have fresh oil or other release agents already applied, you must cast off the previously applied form release agent prior to applying KLIN KOT .
- KLIN KOT must be re-applied to the forms after EACH use. It can be applied at any time by spraying the entire forming system while either setting up or tearing down the system.
- Allow KLIN KOT to turn from white to clear on the face of the forming system prior to pouring concrete.
- This product may also be applied to the backs of the forms to prevent splatters from sticking.
Instructions
Step 1 – Determine Your Mix Ratio
- Please see the above starting mix ratios. Ratios can be adjusted based upon your results. They may be adjusted up or down in one part increments to achieve optimum results.
- NOTE: The more concentrate you add the thicker and more protective KLIN KOT will be.
Step 2 – Mixing
- Using a clean container, add KLIN KOT and water to achieve the recommended ratio for your application. Adding KLIN KOT to water and then adding more water will eliminate the need for mixing. Do NOT mix with diesel, fuels or oils. Do NOT mix with other release agents.
Step 3 – Application
- KLIN KOT may be applied at any time. For best results, the application surface should be cleaned prior to application. Remove all other release agents before applying KLIN KOT .
Step 4 – Spraying
- Spray on and then let change from white to clear before using the treated forms. If KLIN KOT freezes on the surface you are treating, it will still work. Reapply after every use.
Typical Coverage Rates
- 1 gallon of mixed KLIN KOT will cover approx. 2000 square feet, depending on the surface type. Spray on for best performance and ease of application.
Notes
- DO NOT switch back and forth between KLIN KOT and other release agents due to incompatibility.
- Once KLIN KOT has changed from white to clear, it will NOT wash off during rain. However, KLIN KOT can NOT be applied during rain because it will rinse off before the product changes from white to clear.
- If the forms are new, you can season them with KLIN KOT just as you would with oil.
- Proper vibration should be used to achieve the best surface finish. Please see our General Vibration Facts sheet for details.
- In freezing weather, mix product as needed. Concentrate will not freeze however premix may freeze.
| Product Name | RXSOL-16-1690-025 |
| Product Type | Klin Kot |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 65113333 / 5555 / 9999 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| mail@rxmarine.com |
Principal Ingredient:
| Component | OSHA PEL | ACGIH TLV | NIOSH REL | NIOSH Carcinogen | ||||
| --------- | TWA | STEL | TWA | STEL | TWA | STEL | IDLH | --------- |
|
Mineral Oil Blend Concentrate |
5 mg/m3 (oil mist) |
None Established |
5 mg/m3 (oil mist) |
10 mg/m3 (oil mist) |
None Established |
None Established |
None Established |
None Established |
The above information is for KLEEN KOTE Concentrate.
The product is not formulated to be used in a concentrated form. At the strongest recommended mix ratio of 8 parts water to 1 part KLEEN KOTE the mix is 87.5% water.
|
HMIS HEALTH 1 FLAMMABILITY 0 PHYSICAL HAZARD 0 |
****** EMERGENCY OVERVIEW ****** This product is not expected to cause a severe emergency hazard. |
HMIS HEALTH 1 FLAMMABILITY 1 PHYSICAL HAZARD 0 |
Potential Health Effects: See Section 11 for complete toxicological information.
| Inhalation: | Inhalation of vapors or mist may be irritating to respiratory passages. Target organ for mineral oil mist is lungs. Prolonged exposure may result in dizziness and nausea. |
| Eye: | Eye contact may result in slight irritation and redness. |
| Skin: | Short term contact with skin is unlikely to cause any problems; excessive or prolonged and repeated contact and poor hygiene conditions may result in dryness, dermatitis, erythema, oil acne, cracking and defatting of the skin. |
| Ingestion: | May result in nausea or stomach discomfort. |
| Carcinogenicity: |
Based on OSHA 1910.1200 and IARC study requirements, this product does not require labeling. Meets EU requirements of less than 3% (w/w) DMSO extract for total polycyclic aromatic compound (PAC) using IP 346. NTP and OSHA do not list this product as a potential carcinogen. |
| Mutagenicty: | This product gives negative mutagenic results from Modified Ames Assay. |
| Eye Contact: | Flush with water for at least 15 minutes. If irritation develops or persists, promptly contact a physician. |
| Skin Contact: | Wash skin thoroughly with mild soap and water. Remove contaminated articles and get medical attention if irritation develops. Launder articles before reuse and discard saturated articles that cannot be cleaned thoroughly. |
| Inhalation: | Remove exposed person to fresh air if adverse effects are observed. Assist breathing if necessary. Seek medical help. |
| Aspiration: | If there is suspicion of aspiration into the lungs obtain medical advice. |
| Ingestion: | Do NOT induce vomiting. If conscious, give two glasses of water. Seek medical attention immediately! |
|
Notes to Physician: |
Treat symptomatically. |
| Flash Point: | >325 °F ( >163 °C) |
| Flash Point Method: | NA |
| Burning Rate: | Not Available |
| Auto Ignition Temperature: | >600 °F ( >315 °C) |
| Lower Explosive Level: | Not Determined |
| Upper Explosive Level: | Not Determined |
| Flammability Classification: | OSHA Class III-B Combustible Liquid |
| Extinguishing Media: | Halon, CO2, Dry Chemical, Foam, Water Spray or Water Fog. Water may be used to cool below flash point. |
|
Unusual Fire or Explosion Hazards: |
Do not use forced stream as this could cause fire to spread. |
| Combustion Products: | Fumes, smoke and carbon monoxide. |
|
Fire Fighting Instructions and Equipment: |
Water may cause splattering. Use water to cool containers exposed to fire and to protect personnel. Fire fighters should wear proper protective equipment and clothing including respiratory protection (positive pressure if available). |
Personal Protective Equipment must be worn, see Personal Protection Section 8 for PPE recommendations.
| Spill / Leak Procedures: | Spill area will be slick. Stop spill at source if possible. Eliminate sources of ignition. Prevent entry into sewers and waterways. Contain spill. Ventilate area if spilled in a confined space or other poorly ventilated areas. Residual liquid can be adsorbed by inert material. Recover all possible material for reclamation. Dispose of in accordance with all Federal, Sate and Local environmental regulations. |
| Spill to Navigable Waters: | If this material is spilled into navigable waters and creates a visible sheen, it is reportable to the National Response Center at 800.424.8802. |
|
General Handling Procedures: |
Keep containers closed when not in use. Keep away from flames, sparks or hot surfaces. Never use a torch to cut or weld on or near containers. Wash thoroughly after handling. Empty containers contain product residue which may exhibit hazards of the product. Maximum handling temperature has not been determined. |
| Storage Procedures: |
Do NOT store near potential sources of ignition. Rotate stock. Store in clean, dry containers at ambient temperatures and it should remain stable unless it is contaminated. Do NOT store at temperatures greater than 120ıF (49ıC). Maximum storage temperature has not been determined. NFPA Class III-B storage. |
| Work / Hygienic Practices: |
Wash hands with soap and water before eating, drinking, smoking or use of toilet facilities. Do not use gasoline, solvents, kerosene or other harsh or abrasive skin cleaners for washing exposed skin areas. Take a shower after use if general contact occurs. Launder articles before reuse and discard saturated articles that cannot be cleaned thoroughly |
| Ventilation Procedures: | Use with adequate ventilation. |
| Gloves Procedure: | As needed to prevent repeated skin contact. Solvent resistant gloves should be used if needed. |
| Eye Protection: | Safety Glasses |
| Respiratory Protection: | Not normally needed. Use NIOSH/MSHA approved respirator with a dust mist cartridge if the recommended exposure limit is exceeded. |
|
Clothing Recommendation: |
Long sleeve shirt is recommended. Use chemically protective boots when necessary to avoid contaminating shoes. Do NOT wear rings, watches or similar apparel that could entrap the material and cause a skin reaction. |
| Loading Temperature: | Not Determined |
| Flash Point: |
>325 °F ( >163 °C) Cleveland Open Cup (Min.) |
| Specific Gravity (H2O=1): | @ 600F - 0.90 |
| Boiling Point: | Not Determined |
| Vapor Pressure: | Not Determined |
| Percent Volatile: | Nil (LVP-VOC) |
| Vapor Density (Air=1): | > 5 |
| Odor and Appearance: |
Amber liquid with a mild odor. |
| Molecular Weight: | Not Determined |
| pH: | Not Determined |
| Water Solubility: | Dispersible |
| Freezing Point: | Not Determined |
| Evaporation Rate: | Not Determined |
| Viscosity: |
100 SUS @ 100°F (19 cSt @ 40°C) |
| Odor Threshold: | Not Determined |
| Physical State: | Liquid |
| Stability: | This material is normally stable at moderately elevated temperatures and pressures. Avoid sources of ignition. |
| Decomposition Temperature: | Not Determined. |
| Hazardous Polymerization: | Will not occur. |
| Thermal Decomposition: | Smoke, carbon monoxide, aldehydes and other products of incomplete combustion. |
| Incompatibility: | Strong acids, Strong alkalis, Oxidizing agents. |
| Eye Effects: | Minimal irritation possible on contact. Does not meet Canadian D2B or EU R36 criteria. Based on data from components or similar materials. |
| Skin Effects: | Not expected to be a primary skin irritant. Not expected to meet EU R38 criteria. Based on date from components or similar materials. Prolonged or repeated contact, as from wet clothing, may cause drying, defatting of skin and dermatitis. |
| Respiration Irritation: | If material is misted of if vapors are generated from heating, exposure may cause irritation of mucous membranes and the upper respiratory tract. Based on data from components or similar materials. |
| Dermal Sensitization: | No data available to indicate product or components may be a skin sensitizer. |
| Inhalation Sensitization: | No data available to indicate product or components may be a respiratory sensitizer. |
| Exposure Limits: | Contains mineral oil. Under conditions which may generate mists, observe the OSHA PEL of 5mg per cubic meter, ACGIH STEL of 10mg per cubic meter. |
| Chronic Toxicity: | No data available to indicate product or components present at greater than 1% are chronic health hazards. |
| Dermal Toxicity: | Rabbit: LD50>2000 mg/kg. Based on data from components or similar materials. |
| Inhalation Toxicity: | Not expected to be a toxic inhalation hazard. Based on data from components or similar materials. |
| Oral Toxicity: | Rat: LD 50>5000mg/kg. Based on data from components or similar materials. |
| Reproductive Toxicity: | No data available to indicate either product or components present at greater than 0.1% may cause reproductive toxicity. |
| Carcinogenicity: | This material is formulated with mineral oils which are considered to be severely refined and are not considered to be carcinogenic under IARC. All of the oils in this product have been demonstrated to contain less than 3% extractables by the IP 346 test. |
| Mutagenicity: | No data available to indicate either product or components present at greater than 0.1% are mutagenic or genotoxic. |
| Teratogenicity: | No data available to indicate either product or components present at greater than 0.1% may cause birth defects. |
| Freshwater Fish Toxicity: | Not Determined |
| Biodegradation: | Not Determined |
| Saltwater Fish Toxicity: | Not Determined |
| Soil Mobility: | Not Determined |
| Miscellaneous Toxicity: | Not Determined |
| Bioaccumulation: | 0.1-1% of the components display no potential to bioconcentrate |
| Algal Inhibition: | Not Determined |
|
Freshwater Invertebrates Toxicity: |
96 hr. acute static toxicity for Pimephales promelas (Fathead Minnow) LC50 mortality is greater than 30,000 mg/L |
| Bacteria Toxicity: | Not Determined |
| Ecotoxicity: | Available data indicate this product is not acutely toxic. |
| Waste Disposal: | This material, if discarded, is not a hazardous waste under RCRA Regulation 40 CFR 261 if not contaminated. Follow Federal, State and Local regulations. Do not flush to drain or storm sewer. Contact authorized disposal service. Consider recycling. |
|
U.S. Shipping Information: |
Regulation by: D.O.T.: Non-Hazardous. Not regulated by DOT. H.S. Tariff #: 3403.19.0000 Schedule B #: 3403.19.0000 Shipping Class: 55 N.M.F.C.#: 48580 - Sub 3 - Cleaning, Scouring or Washing Compounds, N.O.I., Liquid |
|
Canadian Shipping |
Not regulated under Transportation of Dangerous Goods Act. |
| Other: |
Not Regulated: ICAO/IATA, IMDG (ambient), U.S. Dot Bulk (ambient), U.S. Dot Non- Bulk, TDG Bulk (ambient), TDG Non-Bulk, Mexico, ADR/RID (ambient), ADG (ambient) |
| U.S. TSCA Inventory: | All components of this material are on the US TSCA Inventory. |
|
SARA Extremely Hazardous Substances: |
This product does not contain greater than 1% of any chemical substance on the SARA Extremely Hazardous Substances list. |
| SARA Section 313: | This product does not contain greater than 1% (greater than 0.1% for carcinogenic substance) of any chemical substances listed under SARA Section 313. |
| TDG Regulated Limits: | None Known |
|
CERLA Hazardous Substances: |
None Known |
| V.O.C. Compliant: | Yes |
| Australia: | All components are in compliance with chemical notification requirements in Australia. |
| Canada: | All components are in compliance with the Canadian Environmental Protection Act and are present on the Domestic Substances List. |
| China: | All components of this product are listed on the Inventory of Existing Chemical Substances in China. |
| EU EINECS: | All components are in compliance with the EC Seventh amendment Directive 92/32/EEC. No known R-Phrases or S-Phrases. |
| Japan: | All components are in compliance with the Chemical Substances Control Law of Japan |
| Korea: | All components are in compliance in Korea. |
| Philippines: | All components are in compliance with the Philippines Toxic Substances and Hazardous and Nuclear Wastes Control Act of 1990 (R.A. 6969). |
| Switzerland: | All components are in compliance with the Environmentally Hazardous Substances Ordinance in Switzerland. |
|
California Proposition 65: |
This product is not known to contain any chemicals known the State of California to cause cancer or birth defects. However, we do not conduct routine analysis for all listed materials. |
| Florida: | None Present. |
| Illinois DOL TSL: | None Present. |
| Massachusetts RTK: | None Present. |
| Minnesota RTK: | None Present. |
| New Jersey RTK: | List petroleum oil, but this product does not contain hazardous ingredients. |
| Pennsylvania RTK: | List petroleum oil, but this product does not contain hazardous ingredients greater than 3%. |
This information is furnished without warranty, expressed or implied, except that this information has been compiled from sources considered to be accurate and dependable it is accurate to the best knowledge of the Rx Marine International. The data on this sheet is related only to the specific material designated herein, Progressive Solutions Corporation assumes no legal responsibility for use or reliance upon this data.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.