LIME REMOVER HD is an innovative, concentrated liquid product specifically engineered to attack, penetrate and remove lime deposit accumulations from cargo and storage tanks. It is the liquid product designed to Clean and eliminate limestone caustic lime deposits and dry lime stains from cargo tanks and other large common metal surface installations.
Use For remove heavy lime deposition from metal surface.
It is highly concentrated and powerful penetrating agents materials which is effectively react with lime to loosen the bonding strength . Best results can obtain on dry surface of cement. It break down the ionic bond in lime, releasing the lime from any surface to which it has adhered.
This liquid mixture specifically designed to deal with hard cases of lime cargo deposits or dry lime stains. Its proven advantage is the provision of immediate penetration and complete dissolution of lime, the result being a thorough cleaning.
ACTIVE MATTER : 98-100 %
WHY RXSOL22-2213-210 is better ?
Biodegradable & non flammable , Economical very cost effective
Non-hazardous
Non-fuming
Safe for paint, chrome, aluminum, glass, rubber, plastic, brass & stainless
Dissolves cured cement, concrete, mortar, grout, stucco
Cleans aluminum
Also comes with a foaming spray nozzle
Will not remove rubberized cement
Suitable for the removal of cement deposits and dry stains.
Due to its higher concentration its chemical reaction is very fast.
Lime Remover HD must be used according to the hold surface area that is to be covered, the extent of contamination, the available downtime and the application method being used. Lime Remover HD is covering 10-12 Squire Meter area.
Using Procedure
I - Spray Method
Spray Method is applicable where a high–pressure machine, suitable to process chemical solutions, is used with a 50% Lime Remover HD/water solution to inject directly onto the surface area. Then, the solution must be left to act for 15 minutes followed by thorough rinsing using a high–pressure water supply source. After , the surface must be left to dry. The percentage of dilutions may vary depending on the thickness and hardness of the deposited lime.
II – Soaking Method
Soaking is a method where Lime Remover HD is used undiluted and applied with conventional methods such as an elongated thick and hard brush, a hard sponge etc. Once applied, Lime Remover HD must be left to soak for 30 minutes. Rinse with water, and followed by leaving the surface to dry. Usually, this method is applicable to heavily contaminated small and large tank surface areas and installations.
Lime Remover HD is a concentrated aqueous solution consisting of a blend of special surfactants and specific corrosion inhibitors.
Appearance / Color : Clear liquid
Specific gravity : 1.10–1.20 at 15°C
Solubility in water : 100% Soluble
Boiling Point : 100 °C
Feature and Benefit :
• Ideal for the removal of limestone, birdlime and dry lime stains from all common metal tanks surface and installations.
• Applicable to all metal surfaces and parts except those being galvanized and those made of Tin, Zinc, Aluminum and Lead.
• A water–soluble, non–flammable liquid mixture.
• Can be used to safely neutralize strong alkaline liquids and solids.
• No known effect on rubber or plastic compounds.
• May be combined with a specific range of other products.
• Cost effective, easy to apply and use.
Lime Remover HD is formulated with strong Surfactant agents and special corrosion inhibitors, sufficient enough to neutralize strong alkaline nature of LIME.
| Product Name | RXSOL-22-2213-035 |
| Product Type | Lime Remover HD |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 65113333 / 5555 / 9999 / 27611360 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| mail@rxmarine.com | |
| Website | www.rxmarine.com |
|
Chemical Name |
Concentration |
CAS Number |
EC Number |
R Phrases* |
Symbols |
|
Chlorous mixture |
10-15 |
7647-01-0 |
231-595-7 |
34, 37 |
C |
|
Corrosion Inhibitor |
5-10 |
NA |
NA |
NA |
|
| Proprietory | 30-40 | NA | NA | 34 | C |
*See Section 16
|
Odour |
Strong smell |
|
Appearance |
Liquid, pale yellow, soluble in water |
|
Contact with eyes |
Can cause damage to the eyes |
|
Contact with skin |
Prolonged skin or eye contact may cause chemical burns |
|
Inhalation |
Causes severe irritation, May cause breathing difficulty |
|
Ingestion |
Not regarded as a potential route of exposure.,Causes burning sensation |
|
Contact with skin |
Remove contaminated clothing immediately and drench affected skin with plenty of water. Then wash with soap and water When in doubt or symptoms persist, seek medical attention. Contaminated clothing should be laundered before reuse |
|
Contact with eyes |
If substance has got into eyes, immediately wash out with plenty of water for at least 15 minutes. Irrigate eyes thoroughly whilst lifting eyelids Seek. immediate medical attention. Continue flushing with water until medical help arrives. |
|
Ingestion |
Never make an unconscious person vomit or drink fluids Give plenty of water to drink Do not induce vomiting Seek immediate medical attention |
|
Inhalation |
Remove patient to fresh air Keep warm and at rest, in a half upright position. Loosen clothing. When in doubt or symptoms persist, seek medical attention. |
|
General |
In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible) (S45). |
- Non combustible.
- Smoke from fires is corrosive, Hydrogen chloride may be formed.
- Not flammable. In case of fire use extinguishing media appropriate to surrounding conditions.
- Substance evolves toxic fumes, wear self-contained breathing apparatus.
- Use water spray or fog to knock down and absorb corrosive fumes.
|
Personal Precautions |
Wear protective clothing as per section 8 Vapours are heavier than air and may travel considerable distances to a source of ignition and flashback. |
|
Environmental Precautions |
Do not allow to enter public sewers and watercourses. |
|
Immediate Actions |
Use appropriate containment to avoid environmental contamination (S57). |
|
Clean Up Actions |
Absorb spillage in inert material and shovel up Ventilate the area and wash spill site after material pick-up is complete. |
|
Special Precautions |
Wear protective clothing as per section 8 Avoid release to the environment. Refer to special instructions/Safety data sheets (S61) Vapours are heavier than air and may travel considerable distances to a source of ignition and flashback. |
|
Handling |
Avoid contact with skin and eyes (S24/25).Do not breathe vapour/fumes (S23).Eyewash bottles should be available.Wear protective clothing as per section 8.Ensure adequate ventilation.In use, may form flammable/explosive vapour-air mixture (R18). |
|
Storage |
Keep only in the original container in a cool, well ventilated place (S3/9/49). Keep in acid store. |
|
Exposure Limits |
TLV (TWA) 20 ppm, 122 mg/m3 (1,2-Dichlorobenzene). |
|
Exposure controls |
The undiluted product must not be used in a confined space without good ventilation. |
|
Occupational exposure controls |
Wear approved respirator if exposure likely to exceed MEL/OES Wear goggles giving complete eye protection Wear suitable protective clothing, including eye/face protection and gloves (neoprene or nitrile are recommended). |
 |
 |
|
Odour |
Strong smell |
|
Appearance |
Liquid, pale yellow, soluble in water |
|
PH |
1.5 at 100 % concentration |
|
Boiling point |
~ 100 °C at 760 mm /Hg |
|
Vapour pressure |
105.5 at 20 deg C |
|
Vapour density (air = 1) |
1.26 |
|
Freezing point~ |
30 °C at 760 mm/Hg |
|
Completely soluble in water |
|
|
Specific gravity (water=1) |
1.16 |
|
Non combustible |
|
- This article is considered stable under normal conditions, May cause rubber to swell
- Avoid overheating
- Incompatible with strong oxidizing substances, Contact with alkaline earth metals may form explosive gases, Contact with alkali metals may form explosive gases
- See Section 5
|
Contact with skin |
In cases of severe exposure, redness and irritation may develop |
|
Contact with eyes |
Causes irritation |
|
Ingestion |
May cause gastro-intestinal disturbances |
|
Carcinogenicity |
No evidence of carcinogenic effects |
|
Ecotoxicity |
This product does not contain ingredients which are classified in the EU as dangerous for theenvironment. |
|
Mobility |
Completely soluble in water . |
|
Persistence and Biodegradability |
Its main ingredients will either dissolve rapidly and dissociate in water or are readily/inherently biodegradable. |
|
Bioaccumulation Potential |
Bioaccumulation of the components in this product is insignificant. Other Adverse Effects No environmental problems are expected when the product is used / handled correctly. |
|
Classification |
This material and/or its container must be disposed of as hazardous waste EU Waste class Disposal considerations Do not discharge into drains or the environment, dispose to anauthorised waste collection point Disposal should be in accordance with local, state or national legislation. |
| Proper Shipping Name: | |||||
| UN | |||||
| Proper Shipping Name: | Solution of Phosphoric ang Hydrozen Chlorde | ||||
| UN NO. |
1789 |
||||
| Hazard Class | 8 | PackingGroup | II | ||
|
Road/Rail(ADR/RID) |
|||||
| Proper Shipping Name |
|
||||
| ADR UN No. |
1789 |
||||
|
ADRHazardClass |
8 | Tremcard |
80GC1789-II |
||
| Sear (IMDG) | |||||
| Proper Shipping Name |
|
||||
| IMDG UN No. |
1789 |
||||
| IMDG Hazard Class | 8 | IMDG PackGroup.: |
II |
||
| IMDG EmS | F-A, S-B | IMDG subrisk |
N/A |
||
|
IMDG Labels |
8 |
IMDG Flashpoint: |
N/A |
||
|
Air(ICAO/IATA) |
|||||
| ProperShippingName |
|
||||
| IMDG UNNo |
1789 |
||||
| IMDG HazardClass | 8 | ICAO PackingGroup |
II |
||
| ICAO subrisk | N/A | ICAO Labels: |
8+CAO |
||
| ICAO Flashpoint |
N/A |
||||
|
DOT/ CFR(USDepartment ofTransportation |
|||||
|
DOTProperShippingName |
|
||||
|
HazardousMaterial |
|
||||
| HazardClass | 8 | IdentificationNumber: | UN1789 | ||
|
Product RQ (lbs) |
N/E | DOTsubrisk: |
N/A |
||
|
DOTLabels |
8 |
DOTFlashpoint: | N/A | ||
- Not classified as hazardous for transport
|
Risk Phrases |
Irritating to eyes (R36) |
|
Safety Phrases Irritant |
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice (S26)Wear suitable gloves and eye/face protection (S37/39) |
Text of R and S phrase codes used in this safety data sheet:-
R34 Causes burns;
R36 Irritating to eyes;
R37 Irritating to respiratory system;
R41 Risk of serious damage to eyes.
The information provided about the product on this Safety Data Sheet has been compiled from knowledge of the individual constituents The data given here is based on current knowledge and experience. This Safety Data Sheet describes the product in terms of safety requirements and does not signify any warranty with regard to the product's properties The data given here only applies when product used for proper application(s). The product is not sold as suitable for other applications - usage in such may cause risks not mentioned in this sheet. Do not use for other appli-cation(s) without seeking advice from manufacturer.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.