RXSOL-13-1041-010 is a superior heavy duty and highly concentrated SYNTHETIC CHEMICAL blend of detergents,alkaline salts , emulsifier and chelating agents. A new exciting product with a 3-in-one fuction.
As a floor stripper for all types of waxes and furnishes .
As a degreaser where regular cleaners are unsuitable.
Elimates the need to buy and stock duplicate product .
Excellent stain remover for use on tiles, concrete, wood and other types of hard floor .
Floor Polish Stripper
This is a heavy duty floor polish stripper.
It will remove all kinds of floor polishes with ease. It does not matter whether there is 1 coat of floor polish or 10, GLINT STRIP will remove them quickly and easily.
It can be used on lino, marley tiles, quarry tiles, wood block, etc.
How to strip a floor :::---
The purpose of stripping a floor is to remove all the old floor finish off the floor. Over time floor finish can turn yellow and can build a haze. If burnishing or polishing your floor does not correct this, it's probably time to strip your floors and do a new recoat. Stripping a floor can be a quick and clean procedure if you have the correct tools for the job. The use of a good floor stripper will make your life much easier, it's better to have the floor stripper remove the wax rather than using hard labor. Removing old floor finish is basically a three step process:
Apply the floor stripper and agitate it.
Remove the floor stripper from the floor.
Rinse the floor and neutralize the floor stripper.
Procedure:
Make sure that your floor has been prepared for stripping. Clean the floor removing as much dirt and debris as possible.
After you have the floor has been prepared vacuum or dust mop the floor to remove any dust. We recommend that you spray your duct mop with dust mop treatment to remove as much dust as possible. Make sure to remove anything stuck to the floor because this will gum up or rip the floor pad.
Make sure that the floor are you are stripping does not and will not have traffic moving through it. Use warning signs to make sure the area where you are stripping is marked out so that everyone is aware of the area.
Stripping a floor requires a mop bucket, cotton or blended mop, floor machine (175-300rpm's) and a black or hi-pr stripping floor pad. Follow the specifications for applying the floor stripper. Fill the mop bucket up 1/2 way with floor stripper. Dip the mop into the stripper a lightly wring. Break the floor down into 6' by 6' sections and start applying the stripper to the floor at the furthest corner of the room. Apply the stripper in a figure 8 motion overlapping each stroke by about an inch. After you have applied the stripper let the it sit on the floor for 5-7 minutes. This will give the stripper a chance to react with the floor finish.
Next place a hi-pro or black floor pad on your floor machines. When stripping a floor move the floor machine back and forth on the floor overlapping by at least 1 inch on each pass. As the floor finish is removed from the floor it will become duller. You may need to spend extra time on areas with finish buildup. The main traffic area on the floor will have less buildup than low traffic areas.
Once used the floor machine on the 6' by 6' area remove the stripper from the floor using either a blended mop of wet dry vacuum preferably one that has a front mount squeegee. Do not let the stripper finish mixture dry. if the area does dry apply more stripper to reloosen the finish.
After the you have removed the floor stripper from the floor rinse the floor with warm water. Rinse the floor two more times with cold water.
After the third rinse with plain water, rinse the floor with a floor stripper neutralizer. Neutralizer will reduce the white residue left by the floor stripper so that the floor finish can adhere to the floor much better.
After the neutralizer dries check for white residue on the floor using a black towel. If residue still exists rinse one more time with cold water. Once all these steps have been completed check the floor for shiny spots. If shiny spots are evident you may need to re-strip these areas.
| Product Name | RXSOL-13-1041-010 |
| Product Type | Floor Stripper-II |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 65113333 / 5555 / 9999 / 27611360 |
| Fax | +91 22 2781 1318 :AOH :0091 9821214367 |
| mail@rxmarine.com |
|
Principle Hazardous Component(s) (chemical and common name(s) |
(Cas. No) |
% |
OSHA PEL mg/m3 |
ACGIH TLV mg/m3 |
NTP |
IARC |
OSHA regulated |
|
Sodium Metasilicate Pentahydrate |
(6834-92-0) |
85% |
5 |
10 |
No |
No |
No |
Emergency overview
Appearance : White powder
Immediate effects : Caustic, irritating to skin and mucous membranes. Ingestion causes GI upset.
Potential health effects:
|
Primary Routes of entry |
Inhalation, skin and eye contact. |
|
Signs and Symptoms of Overexposure |
The dust can cause tissue damage, especially to eyes and lungs. |
|
Eyes |
May cause eye irritations or damage. |
|
Skin |
May cause skin irritation. |
|
Ingestion |
Causes GI upset. |
|
Inhalation |
May cause irritations or tissue damage to throat and lungs. |
|
Chronic Exposure |
ND |
|
Chemical Listed As Carcinogen Or Potential Carcinogen |
No |
See Toxicological Information (Section11) Potential environmental effects See Ecological Information (Section 12)
If accidental overexposure is suspected:-
|
Eye(s) Contact |
Flush eyes immediately with water for at least 15 minutes.Get medical attention. |
|
Skin Contact |
Flush immediately with water for at least 15 minutes. Was clothes before reuse. |
|
Inhalation |
Remove victim to fresh air. Administer oxygen if breathing is difficult. |
|
Ingestion |
See medical attention. |
|
Note to physician |
|
|
Treatment |
ND |
|
Medical Conditions generally Aggravated by Exposure |
ND |
|
Flash Point |
None |
|
Flammable Limits |
None |
|
Auto-ignition point |
ND |
|
Fire Extinguishing Media |
None |
|
Special Fire Fighting Procedures |
None |
|
Unusual Fire and Explosion Hazards |
None |
|
Hazardous combustion products |
Carbon monoxide and dioxide when burned |
|
DOT Class |
None |
Steps to be Taken in Case Material is Released or Spilled: Clean up solids. Remnants may be neutralized with weak acid and absorbed for disposal.Waste Disposal Methods : Dispose of waste according to Federal, State and Local Regulations.
|
Precautions to be Taken in Handling and Storage |
Store away from high heat, avoid skin contact |
|
Storage temperature |
Room temperature. |
|
Storage Pressure |
NA |
|
Engineering Controls |
|
|
Ventilation required |
Local exhaust. |
|
Personal Protection Equipment |
|
|
Respiratory protection |
Wear dust mask |
|
Protective gloves |
Rubber or latex. |
|
Skin protection |
Wear gloves |
|
Eye protection |
Safety glasses or face shield. |
|
Additional clothing and/or equipment |
None needed. |
|
Exposure Guidelines |
See Composition/Information on Ingredients (Section2) |
|
Appearance and Physical State |
White powder. |
|
Odor (threshold) |
Mild odor. |
|
Specific Gravity (H2O=1) |
1 |
|
Vapor Pressure (mm Hg) |
Nil |
|
Vapor Density (air=1) |
NA |
|
Percent Volatile by volume |
Nil |
|
Evaporation Rate (butyl acetate=1) |
NA |
|
Boiling Point |
NA |
|
Freezing point / melting point |
NA |
|
pH |
NA |
|
Solubility in Water |
NA |
|
Molecular Weight |
NA |
|
Stability |
Stable |
|
Conditions to Avoid |
None |
|
Materials to Avoid (Incompatibility) |
Strong acids. |
|
Hazardous Decomposition Products |
Carbon monoxide and dioxide. |
|
Hazardous Polymerization |
|
Results of component toxicity test performed: Sodium Metasilicate Pentahydrate (6834-92-0) anhydrous material. Rat (oral) LD50: 1153 mg/Kg. Standard Draize, Skin human, 250 mg/24-hour, severe. Investigated as reproductive effectors. Human experience: ND for product. This product does not contain any compounds listed by NTP or IARC or regulated by OSHA as a carcinogen.
|
Ecological Information |
ND |
|
Chemical Fate Information |
ND |
RCRA 40 CFR 261 Classification:Federal, State and local laws governing disposal of materials can differ. Ensure proper disposal compliance with proper authorities before disposal.
|
US DOT Information |
|
|
Proper shipping name |
Corrosive solid, basic, inorganic, n.o.s. (contains Sodium Metasilicate) |
|
Hazard Class |
8 |
|
Packaging group |
III |
|
UN Number |
UN3262 |
|
Limitations |
See 49CFR173.154(B)(2)(c). |
|
Ground |
ORM-D |
|
IATA |
|
|
Proper shipping name |
Corrosive solid, basic, inorganic, n.o.s. (contains Sodium Metasilicate) |
|
Hazard Class |
8 |
|
Packaging group |
III |
|
UN Number |
UN3262 |
|
Limitations |
See current IATA regulations |
|
IMO |
|
|
Proper shipping name |
Corrosive solid, basic, inorganic, n.o.s. (contains Sodium Metasilicate) |
|
Canadian TDG |
ND |
United States Federal Regulations MSDS complies with OSHA’s Hazard Communication Rule 29, CFR 1910.1200.
|
SARA |
None listed |
|
SARA Title III |
None listed |
|
RCRA |
None listed |
|
TSCA |
Sodium Metasilicate Pentahydrate (6834-92-0). Listed |
|
State Regulations |
|
|
CERCLA |
None listed. |
|
California Proposition 65 |
None listed |
|
International Regulations |
|
|
Canada WHMIS |
Sodium Metasilicate Pentahydrate (6834-92-0). Listed |
|
Europe EINECS Numbers |
ND |
|
Label Information |
Caustic, irritating to eye, skin and mucous membranes. |
|
European Risk and Safety Phrases |
ND |
|
European symbols needed |
ND |
|
Canadian WHMIS Symbols |
|
|
NFPA Hazard Rating: Health |
1; Fire: 0; Reactivity: 1 (0=least, 1=Slight, 2=Moderate, 3=High, 4=Extreme) |
|
Abbreviations used in this document |
|
|
NE |
Not established |
|
NA |
Not applicable |
|
NIF |
No Information Found |
|
ND |
No Data |
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.