Turbine Kleen 81 RXSOL is liquid concentrate Gas Turbine Compressor Cleaner, which is made from surfactant and biodegradable natural enzyme based solvent chemicals. Its consists of corrosion inhibitors and developed to give the maximum possible cleaning efficiency With ultra effectiveness from a natural-solvent chemical. Due to advanced formula based on latest bio - technology make it a very safe & user friendly product for both online & offline compressor cleaning. Usually compressor cleaners are formulated either from anionic, cationic or nonionic surfactants. Turbine Kleen 81 Rx however contains a very complex triple-active formula of cationic, nonionic and amphoteric surfactants, of which the latter is a state-of-the-art surfactant custom made for Turbine Kleen 81 Rx.
It can be used with any on-line/off-line injection system. It is designed to remove the accumulation of atmospheric impurities, oil and oil oxidation products that occurs in the compressor of such engines and so restore the power loss caused by these deposits.
Recommendation dose is 1 part Turbine Kleen 81 Rx with water in the proportion of 1 part 4 parts water. The product has a low trace analysis of inorganic impurities and, in order that the working solution applied to the compressor is equally low in such impurities. Use demineralised water as specified by the engine manufacturer, typically <11μS/cm. The volume of chemical solution needed per wash and the optimum cleaning frequency will depend upon engine size, operating environment and fouling tendency. It is recommended that a post rinse is performed to ensure that the nozzle system is cleaned and ready for next operation.
Turbine Kleen 81 Rx solution is sprayed into the cranked or fired engine, according to the engine manufacturers' approved method, using the equipment and technique appropriate to the engine being cleaned. Allowed to soak for 20 to 30 minutes then thoroughly rinsed off at cranking speed with good quality water acceptable to the engine manufacturer The volume of solution required and the flow rate will depend on engine type. Turbine Kleen 81 Rx can be used with dilution ration 1:2 for offline cleaning, providing a superb cleaning result for heavily fouled compressors
Physical Properties :
|
Appearance |
: |
Fluid |
|
Colour |
: |
Light yellow |
|
Odour |
: |
Characteristic |
|
Odour threshold |
: |
Not determined |
|
pH-value at 20°C |
: |
7-8 |
|
Melting point/Melting range |
: |
<0°C |
|
Boiling point/Boiling range |
: |
110°C |
|
Flash point |
: |
NA |
|
Flammability (solid, gaseous) |
: |
Not applicable |
|
Ignition temperature |
: |
225°C |
|
Decomposition temperature |
: |
Not determined |
|
Self-igniting |
: |
Product is not self-igniting |
Advantage :
Easy and safe to use: Turbine Kleen 81 Rx is non-aggressive against the eyes and skin. When using the product no special precautionary measures other than standard safety procedures for the application of cleaning products need be observed.
Easy disposal: Turbine Kleen 81 Rx is biodegradable in any biological sewer system. Disposal of the off-line wash effluent therefore is determined by the engine fouling found in the solution.
Easy to handle and supply : Turbine Kleen 81 Rx is normally supplied as an industry standard 1:4 concentrate. For those that prefer the convenience of a ready to use product Turbine Kleen 81 Rx can be supplied pre-diluted. All variants are available in 1,000 ltrs IBCs, 210 litres drums, 25 and 20 litres containers.
FUTURE & BENEFIT :
- Safely and effectively cleans compressors on-line when running at any speed and load.
- Extremely effective non-solvent cleaner.
- Meets the most stringent requirements of gas turbine manufacturers.
- Ideal for light and frequent on-line washing of any type of industrial, marine or aviation gas turbine to maintain in-service output and fuel efficiency.
- On-line cleaning reduces damaging shutdown/start-up thermal cycles and starter wear and tear.
- Ideal for off-line cleaning due to high biodegradability.
- Non-flammable.
- Mixes readily with most antifreeze agents to allow low ambient temperature on-line/off-line cleaning.
- Supplied in concentrated form to reduce transport and handling costs and minimize storage requirements.
Note :
Before operating the process described it is important that this complete document, together with any relevant Safety Data sheets, be read and understood.
| Product Name |
Turbine Kleen 81 RX |
| Product Type | RXSOL-81-8185-025 |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point : Mumbai, Kandla, Kolkata, Chennai, Vizag, Fujairah, Muscat, Nairobi
| Phone | +91 22 65113333/ 5555 / 9999 / 27611360 / 27815540 |
| Fax | +91 22 2781 1318 :::AOH :0091 9322594669 |
| mail@rxmarine.com |
Proprietary mixture of non-ionic surfactant and emulsifier in deionised water solution.
Hazardous ingredient CAS No. EINECS No. Conc. % Symbols R Phrases
Ethoxylated branched 068439-46-3 polymer 20-40 Xn R22, R41
oxoalcohols
2-(2-butoxyethoxy)ethanol 000112-34-5 203-961-6 1-15 Xi R36
Classification of the mixture: This preparation is classified as dangerous according to Directive 1999/45/EC.
Harmful: Harmful if swallowed. Irritant: Risk of serious damage to eyes.
Label elements: Xn Harmful (contains ethoxylated C9-11 alcohols) Danger Symbols:
Risk phrases: R22. Harmful if swallowed.
R41. Risk of serious damage to eyes.
Safety phrases: S26. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S36/37/39. Wear suitable protective clothing, gloves and eye / face protection.
Other hazards: none known.
Description of first aid measures:
Contact with skin: Remove contaminated clothing. Wash skin immediately with plenty of soap and water. If symptoms develop, get medical attention.
Contact with eyes: Wash immediately with eyewash solution or clean water, holding eyelids apart, for at least 10 minutes. Get immediate medical attention.
Ingestion: Rinse mouth with clean water. Get immediate medical attention.
Inhalation: Not expected to present a significant inhalation hazard under conditions of normal use.
Most important symptoms and effects, both acute and delayed: Risk of serious damage to eyes. May cause eye damage if untreated.
Indication of any immediate medical attention and special treatment needed: Treat symptomatically.
Extinguishing media: In case of fire use water, foam, carbon dioxide or dry agent.
Special hazards arising from the mixture: Product has no flash-point, but if heated sufficiently, it will produce flammable vapours.
Advice for firefighters: Use water spray to cool containers exposed to fire and to protect personnel. Firefighters should wear full protective gear including S.C.B.A. sets with full face shields.
Personal precautions, protective equipment and emergency procedures: Wear protective clothing as described in Section 8 of this safety data sheet.
Environmental precautions: Dispose of in accordance with local regulations. The appropriate regulatory
body must be alerted to spillages or uncontrolled discharges to watercourses
Methods and material for containment and cleaning up: Dike and contain spill. Do not allow spill to enter drains, sewers or waterways, ground, plants and vegetation. Recover free liquid if possible. Absorb spillage with inert material, floor absorbent, earth or sand and collect into appropriate containers.
Precautions for safe handling: Avoid contact with skin or eyes. Otherwise, no particular precautions are required in normal use. Practice normal industrial hygiene. Provide adequate ventilation. May present slip hazard if spilt.
Conditions for safe storage, including any incompatibilities: Keep containers closed to prevent contamination when not in use. Do not store near heat, open flames or strong oxidants. Store containers in an adequately ventilated area, protected against the sun (under a roof) and direct exposure to the weather (rain, storms, etc.). Do not store the product at temperatures below its freezing point.
Specific end uses: Industrial uses (SU3); Use in closed, continuous process with occasional controlled exposure (PROC2); Industrial use of substances in closed systems (ERC7); Washing and cleaning products, including solvent based products (PC35). No Exposure Scenario is available for this mixture.
Control parameters: Component substances with Workplace Exposure Limits
LTEL, 8hr.TWA STEL Time Authority
Component substance ppm mg/m3 ppm mg/m3
2-(2-butoxyethoxy)ethanol 10 67.5 15 101.2 15 mins. UKHSE
EH40/2005
2-(2-butoxyethoxy)ethanol (EC No. 203-961-6):
Derived No Effect Level (DNEL) -Industry Dermal Long Term 20 mg/kg/day
DNEL -Industry Inhalation Long Term 67.5 mg/m3
Exposure controls:
Wear suitable protective clothing, including eye/face protection and gloves.
Protective gloves must be used if there is a risk of direct contact or splash. Nitrile rubber offers best long-term protection, be aware that the liquid may penetrate the gloves. Frequent change is advisable.
Manufactured/tested in accordance with EN 374.
If ventilation is insufficient, adequate respiratory protection must be provided. At work in confined or poorly
ventilated spaces, respiratory protection with air supply must be used. Where air-filtering respirators are appropriate, select a mask & filter combination suitable for aerosols and vapours such as Type-A or Type -
2, ABEK-2 in accordance with EN 141. Check that mask fits tight and change filter regularly.
Information on basic physical and chemical properties:
|
Appearance |
Clear, blue, low viscosity liquid at 20oC |
|
|
Odour |
Characteristic, sweet. |
|
|
Change in physical state |
Boiling point |
approx. 100oC (212°F) |
|
Pour point |
-1oC (30°F) |
|
|
Flash point |
>100oC (212°F) (Closed Cup) |
|
|
Auto-ignition temperature |
not determined |
|
|
Flammability limits in air |
LEL |
not applicable |
|
(% vol. in air) |
UEL |
not applicable |
|
Vapour pressure at 20oC (68°F) (non-water fraction) |
0.01 kPa |
|
|
Solubility in water: |
Complete |
|
|
pH Value |
7-8 |
|
|
Relative density at 15oC (59°F) |
1.007 g/cm 3(8.41 lb/US Gal) |
|
|
Viscosity (ASTM D 445) @ 27oC (80°F) |
12 mm 2/s |
Other information: The above data are typical values and do not constitute a specification.
Reactivity: Reacts with oxidising agents.
Chemical stability: Stable in normal use and under recommended storage conditions.
Possibility of hazardous reactions: Other than 10.1, none known.
Conditions to avoid: Avoid excessive heat for prolonged periods of time. Avoid exposure to high temperatures or direct sunlight. Avoid freezing conditions.
Incompatible materials: Strong oxidising agents.
Hazardous decomposition products: Product stable under normal conditions of storage, handling and use.
Information on toxicological effects:
Acute effects:
Inhalation:No significant signs or symptoms indicative of any health hazard are expected.
Ingestion:May cause nausea, vomiting and diarrhoea.
Skin contact:May cause drying of the skin and contact dermatitis.
Eye contact:May cause serious eye irritation.
Chronic effects:No experimental data are available on this preparation. Based on chronic toxicological information on its components it is unlikely to pose a carcinogenic, mutagenic or reproductive toxicity risk to humans if exposure is maintained at or below occupational limits.
Toxicity: The product has a low order of acute toxicity to aquatic species:
Acute toxicity of effluents and receiving waters to freshwater and marine organisms
according to EPA/600/4-90/027 "Methods for measuring" :
Cladoceran (Ceriodaphnia dubia) : 48 hours LC50 : 10 ppm
Fathead Minnows (Pimephales promelas) : 96 hours LC50 : 15 ppm
Persistence and degradability: The product is expected to degrade rapidly in the aquatic environment. Product tested according to OECD-302B "Inherent biodegradability, modified Zahn-Wellens Test", exposed to activated sludge of a municipal biological sewage waste water treatment plant under aerobic static conditions. Based on individual dissolved organic carbon (DOC) determinations TURBOTECT 950 reached a biodegradation of 99 % after 7 days, and at the end of this 28 day test, 88% of the organic carbon had been transformed into CO2. TURBOTECT 950 showed no significant toxic effects to the activated sludge, indicating no inhibition of the nitrifying micro-organisms.
Total organic carbon (TOC): 221 mg C /g TURBOTECT 950;
Chemical oxygen demand (COD): 747 mg O2/g TURBOTECT 950. TURBOTECT 950 is therefore classified as easily biodegradable under the strict terms and conditions of the OECD Guideline No. 302B. A copy of the relevant test report is available on request.
Bio-accumulative potential: The product has low potential for bioaccumulation.
Mobility in soil: no data available.
Results of PBT and vPvB assessment: Not Classified as PBT/vPvB by current EU criteria
Other adverse effects: The product is not a “VOC” (Volatile Organic Compound), the vapor pressure (calculated) for the non-water components is 0.075 mm Hg / 20°C (0.01 kPa).
Waste is classified as hazardous waste. Disposal to licensed waste disposal site in accordance with the local waste disposal authority.
Waste treatment methods: The product and effluent resulting from its use should not be released into the environment. Dispose of in accordance with the European Directives on waste and hazardous waste. Dispose of in accordance with local regulations. Empty containers may contain flammable or explosive vapours. Do not burn, or use a cutting torch on, the empty drum. Empty containers should be taken to an approved waste handling site for recycling or disposal.
UN Number: none
Not Dangerous Goods according to international transport regulations
Transport hazard class(es): none
Packaging group:
Environmental hazards: Not a Marine Pollutant
Special precautions for user: none
Transport in bulk according to Annex II of Marpol 73/78 and the IBC code: not available
Safety, health and environmental regulations / legislation specific for the mixture: none applicable.
Chemical safety assessment: No Chemical Safety Assessment has been carried out for this mixture by the supplier.
This product has no established regulatory information. All regulatory information given is based on individual components of the mixture by component number. While this information and recommendations set forth herein are believed to be accurate and reliable, it is provided without warranty regarding its accuracy.
RX MARINE INTERNATIONAL MAKES NO WARRANTY WITH RESPECT HERE TO AND DISCLAIMS ALL LIABILITY FROM RELIANCE THEREON.
Users must determine safe conditions for use and assume liability for any loss, injury, damage or expense resulting from use of this product.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.