Metal Rust remoing cleaner and detergent, Specially designed for removal of rust from any steel surface area and rust stains from stainless steel, brass, copper, , aluminum, wood and ceramic surfaces.
Also acts as a surface brightener. It is a superior heavy duty and highly concentrated liquid blend of surfactants & organic compounds containing rust penetrating agents, solubilizer and inhibitors. Acts as rust proofing agent before the application of paint or coatings. It is non-flammable. Prevents further rusting.
For steel surfaces remove oil, grease and old paint. Wet down entire surface with neat Metalic Brightner Eco Rust Clean and allow to dry. Second wash may be necessary. Surface should have a grey/white appearance when the Metalic Brightner Eco Rust Clean is dry. Steel surfaces will have a resistance to rust and will render a good base for paint.
For removal of rust stains on painted surfaces and wood, Metalic Brightner Eco Rust Clean should be applied at full concentration for heavy stains, or diluted to 20-50% for light stains. Allow to soak for 15 to 30 minutes and wash off with water. A second application may be necessary to remove the stubborn stains.
It should be applied in full concentrated for heavy stains, or diluted with 20-50% with fresh water for light strains.
•RXSOL-20-2054-210 is highly concentrate
•Dilute in water (always use plastic jar and RXSOL-20-1011-MB should be added towater never add water to RXSOL-20-2054-210 )
•Surface should be sound clean and free from oil, grease, dirt etc.
•Diluted materials apply on rusted area for 15 to 20 minutes then wash off with water repeat if necessary. (For stubborn rusted stains.)
Spraying Direction: Using an empty / clean 210 liter drum, fill with 190 liter of fresh water and add 20 liters of Metal Clean Bright RXSOL This makes a 10% solution, which can be sprayed onto areas in coated tanks where rust stains are showing and over actual rusted areas. Once spraying is completed, wait 20-30 minutes and fresh water rinse with lots of water, if possible use butterworth machines for a more efficient result. This method can be used in stainless tanks to “freshen up” the look of the stainless materials. Make sure to rinse the tank very well, as residual detergent within the Metal Clean Bright Rx will show up in a Wall Wash.
Injection – Not suitable.
Re-circulation: When hand spraying is inadequate (too much area to cover), prepare a 2% - 5% solution in the tank using fresh water, heat solution to 50o C, then circulate the solution through butterworth machines for 3 x 45 minutes drops minimum. When using fixed machine recirculate for a minimum of 3 cycles. Rinse out the tank using hot seawater 85o C for 2 hours making sure that there is no form remaining in the water at the pumpstack drain cock. After the hot wash, the tank must be rinsed with fresh water and dried.
*If the mixture is allowed to overheat, it will soften epoxy / phenolic coating.*
Use a strainer at the pumpstack when circulating any solution. Tank Lining–Stainless / Epoxy, Phenolic
Product Properties:
| Appearance | Colourless liquid | |
| Density | g/cm3 at 15°C: 1.2 | |
| pH | 10% solution 1.5-2.5 | |
| Compatibility:Metal | Concentrate and long touch may corrode. | |
| Rubber | No known effect | |
| Packaging | Order No: RXSOL-20-2054-210 | Size (in litres) 25 , 35 |
Characteristics:
• Non-flammable.
• Non-flammable.
• Economical,cost effsctive.
• Surface brightening
• Protects and maintains from corrosion
• Acts as rust proofing agent before the application of paints or coatings.
• It doesn’t affect rubber and plasticcompounds
Note:- When cleaning aluminium, brass & copper flush with water upon completion of cleaning
| Product Name | RXSOL-20-2054-210 |
| Product Type | METALLIC BRIGHTENER - Eco RUST CLEAN |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 65113333 / 5555 / 9999 / 27611360 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| mail@rxmarine.com |
Phosphoric Acid ( 10-30 7664-38-2 231-633-2 34 C ) and 2-2(butoxyethoxy)ethanol ( 1-5 112-34-5 203-961-6 36 Xi )
Non classified ingredients 20-60 remaining which is not in the list of hazardous materials.
|
Odour |
Odourless. |
|
Appearance |
Liquid, pale yellow, soluble in water. |
|
Contact with eyes |
Can cause damage to the eyes. |
|
Contact with skin |
Causes burns (R34). |
|
Inhalation |
Vapours or aerosols may cause irritation of eyes, nose and respiratory tract, Can cause damage to the lungs. |
|
Ingestion |
The ingestion of significant quantities may cause damage to digestive syste. |
|
Inhalation |
After inhalation medical attention require |
|
Skin Contact |
In case of contact with skin , wash immediately with plenty of water and soap Remove contaminated clothes. |
|
Eye Contact |
Flush with running water for at least 15 minutes Immediately medical attention require. |
|
Ingestion |
seek medical attention , try to drink more plenty of fresh water. |
|
Non combustible product |
|
|
Suitable |
Not known , on direct exposure to heat dangrous emission of gas of COx SOx can be released |
|
Not suitable |
Not applicable |
|
Special |
Not applicabe |
|
Protection of fire Fighter |
Not applicable |
|
Precaution for fire-fighters |
Wear protective equipment with breathing apparatus. |
|
Enviromental Precaution |
Direct flow into drainage system, surface or ground water is prohibited. First of all neutralize with alkaline materials like lime powder for pH balancing between 6-10. |
|
Cleaning Method |
Flush Spill Area with Water and avoid contact with skin and eye. |
|
Condition to Avoid |
Non flammable but avoid direct heating |
|
Materials to Avoid |
Do not subject to ALKALINE medium. |
|
Handling |
Keep Container Tightly Closed |
|
NOTE |
Eyewash facilities require at workplace |
|
The product causes corrosion on skin and mucous membranes Pl. Note that In case of discharge of acidic or alkaline products into the sewerage system the pH must be in the range of 6-10 since higher or lower pH values may damage the sewerage system or impair biological dosage treatment plants. So that for maintaining pH we have to add acidic / basic medium neutaliser . For example if pH is less than 6 basic neutraliser is required and if pH is more than 10 acidic nature neutraliser is required. For details of any guideline pl. Visit our technical website www.rxmarine.com |
|
|
Personal protection: |
|
|
Respiratory System Protection |
Approved respirator must be worn when spraying |
|
Eye Protection |
Strictly wear eye protection |
|
Hand protection |
wear PVC chemical resistance protective gloves |
|
Appearance |
Clear brownish liquid |
|
Density |
g/cm3 at 15°C: 1.5 |
|
pH |
10% solution 1.5-2.5 |
|
Flash Point |
Not applicable |
|
Compatibility |
|
|
Metal |
Concentrate and long touch may corrode. |
|
Rubber |
No known effect |
|
Hazardous Decomposition Products |
Do not occur if stored and used as directed. In FIRE combustion CO, CO2 , NH3 , SOX etc hazardous gas produced. |
|
NOTE |
AVOID CONTACT WITH ALKALINE SUBJECT. |
|
Skin Irritation |
Cause severe irritation |
|
Eye Irritat |
Cause severe irritation |
|
Sensitization |
Cause Sensitizing |
|
Chronic Toxicity |
Not Identified |
|
Carcinogencity |
No. |
RXSOL MB 1011 is degradable , and due to highly acidic in nature must be neutralized as per guidance and ingridents used in it.Direct contact is Harmful to aquatic organism.
As per guide line of local rules and regulation and before disposal and neutralization pl. refer 07 article.
|
Transport over land ADR/RID |
1805 8/11c 8/11c |
|
Transport over inland waterways ADN/ADNR |
|
|
Transport over sea IMDG |
8 |
|
Transport by air ICAO/IATA |
8/1805 |
|
Phosphoric acid |
|
|
sea |
EMS 8-08, MFAG 700 PG III |
|
Classification and labelling according to 4. Novelle Gefahrstoff-Verordnung |
|
|
Symbols of danger |
C Corrosive |
|
Ingredients |
Phosphoric acid |
|
R-phrases |
R34 : Cause burns |
|
S-phrases |
S26 : In case of contact with eyes, rinse immediately with plenty of water and seek medical. advice. S45 : In case of accident or if you feel unwell, seek medical advice immediately |
|
National prescriptions |
|
|
Water hazard class (WGK) |
2 (self classification on the basis of component assessments or analogy conclusions without addition/subtraction of points for good/poor biodegradability etc.) |
| This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is intended to describe our products from the point of view of safety requirements and is not intended to guarantee any particular properties. |
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.