RUSTOCIDE is a Specially designed for removal of rust from any steel surface area and deposits. Also acts as SURFACE BRIGHTNER. Superior heavy duty and highly Concentrated liquid blend of surfactant & organic compound containing rust penetrating agent, solubilizer and inhibited with rust dissolving acid.
RUSTOCIDE is a single component sulfate and chloride-free liquid, which in one operation removes rust and prevents further rusting of steel.
Dilutions must be made in a plastic container. The acid should always be added to water, never the reverse.
To clean surfaces after welding or rusted surfaces use 50% Rust Remover-Water solution.
To remove stain or rust from brass and copper surfaces use between 20 – 50 % solution and rinse it with water after 15 –40 minutes.
On aluminum surfaces use 10 – 30% Metals Rust stain metal bright surface Cleaner -Water solution and after 5 minutes rinse it with water.
To remove rust from painted surfaces use 20 – 30% Metals Rust stain Brites surface Cleaner -Water solution and rinse with water after 15 - 40 minutes
To remove rust remains from ceramic, porcelain and glass surfaces; use 20 – 50% Rust Remover-Water solution for 20-40 minutes and rinse it with water.
To remove light cement and lime use 50% Rust Remover-Water solution and after 30 – 40 minutes rinse with water.
To remove rust in the pipelines and tanks use 5% Metals Rust stain Brites surface Cleaner -Water solution and circulate. On the other hand, if you use injection method use 3-5% Metals Rust stain Brites Cleaner -Water solution. Both circulation and injection must continue until the rust is removed.
Brushing is recommended for heavy rusty surfaces.
Procedure for Use:-RXSOL-15-1011-210 is highly concentrate
Dilute in water (always use plastic jar and RXSOL-15-1011-210 should be added to water never add water to RXSOL-15-1011-210.)
Surface should be sound clean and free from oil, grease, dirt etc.
Diluted RUSTOCIDE apply on rusted area for 15 to 20 minutes then wash off with water repeat if necessary. (For stubborn rusted stains.)
Spraying Direction: – Using an empty / clean 210 liter drum, fill with 190 liter of fresh water and add 20 liters of RUSTOCIDE Metals Rust stain Brites Cleaner This makes a 10% solution, which can be sprayed onto areas in coated tanks where rust stains are showing and over actual rusted areas. Once spraying is completed, wait 20-30 minutes and fresh water rinse with lots of water, if possible use butterworth machines for a more efficient result. This method can be used in stainless tanks to “freshen up” the look of the stainless materials. Make sure to rinse the tank very well, as residual detergent within the RUSTOCIDE Metals Rust stain Brites Cleaner will show up in a Wall Wash.
Injection– Not suitable.
Re-circulation: – When hand spraying is inadequate (too much area to cover), prepare a 2% - 5% solution in the tank using fresh water, heat solution to 50o C, then circulate the solution through butterworth machines for 3 x 45 minutes drops minimum. When using fixed machine recirculate for a minimum of 3 cycles. Rinse out the tank using hot seawater 85o C for 2 hours making sure that there is no form remaining in the water at the pumpstack drain cock. After the hot wash, the tank must be rinsed with fresh water and dried.
* If the mixture is allowed to overheat, it will soften epoxy / phenolic coating. *
Use a strainer at the pumpstack when circulating any solution. Tank Lining – Stainless / Epoxy, Phenolic
Product Properties:-
|
Appearance |
Colourless liquid |
|
|
Density |
g/cm3 at 15°C: 1.2 |
|
|
pH |
10% solution 1.5-2.5 |
|
|
Compatibility Metal |
Concentrate and long touch may corrode. |
|
|
Rubber |
No known effect |
|
|
Packaging |
Order No:RXSOL MB 1011 HD |
Size (in litres) 25 , 35 |
Characteristics:-
• Non-flammable.
• Prevents further rusting.
• Economical , cost effsctive.
• Surface brightening
• Protects and maintains from corrosion
• Acts as rust proofing agent before the application of paints or coatings.
• It doesn’t affect rubber and plastic compounds
Note:- When cleaning aluminium, brass & copper flush with water upon completion of cleaning
RUSTOCIDE is Specially designed for removal of rust from any steel surface area and rust stain from Brass , Copper , S.S wood , ceramic and aluminium surfaces , painted or not . And RUSTOCIDE acts as surface brightner.
RUSTOCIDE is vastly used for polishing almost all metals, such as brass, copper, nickel, chrome, stainless steel, aluminium and even for machinery and golf clubs.
RustoCIDE is Rust Cleaning detergent with advanced formulation with Non Ionic Detergent and Mixture of Inhibited Acid.
| Product Name | RXSOL-15-1011-210 |
| Product Type | RUSTOCIDE |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point : Mumbai, Kandla, Chennai, Ennore, Visakhapatnam, Gangavaram, Kolkata, Haldia, Fujairah UAE, Muscat Oman
| Phone | +91 22 27815540 / 41 / 42 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| mail@rxmarine.com |
|
Ingredients name |
CAS-NO |
Cons.(weight%) | Classification |
|
Phosphoric Acid with Ethoxylated Fatty alcohol |
|
15-20 | Xi;R36 |
|
Butylene Glycol |
112-34-5 | 10 - 20 | |
| Proprietory Formulatory Detergent Product | 10 | ||
| Citric Acid mixture | 2-4 | C;R34 |
|
Legend T+=Very toxic, T=Toxic, C=Corrosive, Xn=Harmful, Xi=Irritant, IK=No classification required, E=Explosive, O=Oxidising, F+=Extremely flammable, F=Very flammable, Fo=Flammable, N=Dang. to the environment, Mut=Genetoxic, Sens=Sensitizing, Carc=Carcinogen, Repr=Causes birth defects |
Non Hazardous ::: Blend
Acidic liquid. R34 Causes burns. R36 - Irritating to eyes.
| Odour | Odourless |
| Appearance |
Liquid, pale yellow, soluble in water |
| Contact with eyes | Can cause damage to the eyes |
| Contact with skin | Causes burns (R34) |
| Inhalation | Vapours or aerosols may cause irritation of eyes, nose and respiratory tract, Can cause damage to the lungs |
| Ingestion |
The ingestion of significant quantities may cause damage to digestive syste |
|
Inhalation: |
Remove victim from immediate source of exposure and assure that the victim is breathing. Administer oxygen if available. Seek immediate medical attention. |
|
Skin: |
Wash skin with plenty of soap and water for at least 15 minutes. Seek medical attention. Remove contaminated clothing and shoes and clean before reuse or discard if they cannot be thoroughly cleaned. |
|
Eyes: |
Hold eyelids open and flush with a steady, gentle stream of water for at least 15minutes. Seek immediate medical attention preferably with an ophthalmologist. |
|
Ingestion: |
Contact a physician or emergency medical facility immediately. Never give anything to an |
Proper Fire Fighting Equipment: Water spray, fog or mist, alcohol-resistant foam, dry chemical, carbon dioxide (CO2).
Improper Fire Fighting Equipment: Fire fighters should wear self contained breathing apparatus and full protective clothing. Keep unnecessary people away, isolate hazard area and deny entry. Dike area to prevent run off and contamination of water sources. Persons who have been exposed to contaminated smoke should be immediately examine by a physician and checked for symptoms of poisoning.
Fire and Explosion Hazards Products: Oxides of Phosphorous.
Personal Protection When Fire Fighting: Wear self-contained breathing apparatus or supplied-air respirator in confined spaces.
Other Information: Containers close to fire should be removed immediately or cooled with water.
Safety Measurements to Protect Persons: Wear appropriate protective gear for the situation. See personal protection information in section 8.
Safety Measurements to Protect Environment: Run off from fire control or dilution water may cause pollution. Large spills should be handled according to a predetermined plan.
Proper Methods For Damage Limitation And Clean up: Carefully neutralize spill with soda ash. Clean up residual material by washing up area with water.
Handling Advice: Do not get on skin or in eyes. Avoid breathing vapors and mists. Do not ingest. This product reacts violently wit bases liberating heat and causing sputtering.
Storage: Store in an area that is cool, dry, well ventilated.
EXPOSURE LIMITS
Name of Substance: Phosphoric Acid
Page Number:2/5
OSHA (PEL): 8 hour time-weighted average 1 mg/m3
ACGIH (TLV): short term exposure limit 3 mg/m3
ACGIH (TLV): time-weighted average 1 mg/m3
Eye protection: Eye contact should be prevented through use of chemical safety glasses with side shields or splash proof goggles. An emergency eye wash must be readily accessible to the work area. Face contact should be prevented through use of a face shield.
Skin protection: Skin contact should be prevented through use of suitable protective clothing, gloves and footwear, selected with regard for use conditions and exposures potential. Consideration must be given both to durability as well as permeation resistance..
Respiratory protection: When respirators are required, select NIOSH/MSHA approved equipment based on actual or potential airborne concentrations and in accordance with the appropriate regulatory standards and industrial recommendations. Other Information: Do not smoke in work area.
|
Form: |
Liquid |
|
Air Active: |
Not applicable |
|
Colour: |
Colorless |
|
Rel. vapour density: |
Not applicable |
|
Odor : |
Odorless |
|
Ignition temp: |
>450°C |
|
Solubility in Water: |
|
| Moleculer weight: | Not applicable |
| Expl.limit: | Not established |
| MeltingPoint/range: |
Not established |
| Density: | 1.18 – 1.28 gram / cm3 |
| Vapour pressure: | 2.16-5.65 mmHg at 760°C |
| Boiling Point : | 135°C – 158°C at 760mmHg |
| Saturaction conc : | Not applicable |
| Decomposition temp.: | Not applicable |
| Viscosity: | Not established |
| Flash Point: | Not applicable |
| pH: | 1.2 – 2.0 |
Stability: Stable under normal use conditions.
Materials to be avoided: Fluorine, Strong Oxidizing Agents, Strong Reducing Agents, Bases, Metals, Sulfur Trioxide, Phosphorus Pentoxide.
Conditions to be avoided: None known.
Other Information: Hazardous decompositions products Oxide of phosphorus.
TOXICOLOGICAL DATA
Name of Substance: Phosphoric Acid
LD50 (oral, rat): 1530 mg/kg (anhydrous substance)
LC50 (inhalation, rat) : >0.85 mg/l /1 h (anhydrous substance)
LD50 (dermal, rabbit): 2740 mg/kg (anhydrous substance)
Inhalation: Mists can cause lung irritation, shortness of breath, fluid in lungs.
Skin contact: Causes irritation and skin burns.
Eye contact: Corrosive, causes tissue destruction, permanent damage to the cornea, blindness.
Ingestion: Can cause nausea, vomiting, diarrhoea, corrosion, burns to mouth and oesophagus, abdominal pain, chest pain, shortness of breath, seizures, death.
ECOTOXICOLOGICAL DATA
Name of Substance: Phosphoric Acid
Fish toxicity: fish LC50: 138 mg/l
Aquatic organisms LC50: 100-1000 mg/l 96 h
Mobility: Completely soluble in water.
Breakdown: No specific biodegradation test data locate. While acidity of this material readily reduced in natural waters, the resulting phosphate may persist indefinitely or incorporate into biological systems.
Other Information: Depending on the concentration, phosphorus compounds may contribute to the eutrophication of water supplies.
This material and / or its container must be disposed of as hazardous waste. Do not empty into drains or the environment, take it to an authorized waste collection point. Disposal of local, state or national legislation must.
ADR
Goods classified for transport : YES
UN-no : 1805
Proper shipping name : PHOSPHORIC ACID, LIQUID
Packing group : III
ADR class : 8/17c
ADR : 8/17c
UN
UN-no : 1805
Class : 8
Packing group : III
IMCO
UN-no : 1805
EmS :F-A,S-B
Class : 8
Packing group : III
C;Corrosive
R-PHRASES R34 Causes burns.
R36 - Irritating to eyes.
S-PHRASES S2: Keep out of the reach of children.
S26: In case of contact with eyes rinse immediately with plenty of water and seek medical advice.
S36/37/39:Wear suitable protective clothing, gloves and eye/face protection.
S45:In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible).
Dated 26.12.2008 of the Ministry of Environment HAZARDOUS SUBSTANCES AND PRODUCT CLASSIFICATION, PACKAGING AND LABELLING REGULATIONS according to classified.
This safety data sheet has been prepared on the basis of information given by our suppliers and our present knowledge. Information given is intended to present guidelines for safe handling, use, processing, storage, transport, disposal and discharge; it is not intended to be a guarantee or quality specification. The intent of this safety data sheet is to give a description of the product with regard to safe storage, handling and use. Information given applies only to the product itself, and not in combination with other products or in any processed form, unless this is specified in the text. We believe that all information in this safety data sheet (which replaces all previous versions) was correct at the date of issue. It is the responsibility of the recipient of this safety data sheet to ensure that information given here is read and understood by all who use, handle, dispose of or in any way come in contact with the product.
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.