Well balanced alkaline cleaner. It is free hydrocarbon solvents. Gentle & suitable for tank cleaning operation. A very strong alkaline cleaner, which can be used to soften up / remove baked on drying oils and also used after animal and vegetable oils, fish oils, tall oils, tung oil etc. It is a low toxic product with an exceptional solvency power on soil & oily matter.It is free from Hydrocarbon solvents , Biodegradable and minimizes the extreme hazards to personnel in handling materials.
This is a high-performance, concentrated cleaning solution developed for the effective removal of a wide range of organic and hydrocarbon-based residues. It is suitable for cleaning vegetable and animal oils, fats, fuel oils, lubricating oils, coal residues, and related deposits from cargo tanks, storage tanks, and associated systems.
The formulation is also highly effective for removing various coal cargo residues from ship cargo holds, as well as carbonaceous and exhaust-related deposits commonly found in vessel garage areas, ceilings, walls, roof structures, and hull surfaces.
Its powerful concentrated formulation provides rapid penetration and efficient soil removal, helping restore heavily contaminated surfaces with minimal cleaning effort. In addition to its cleaning action, the product helps neutralize and eliminate persistent unpleasant odors, leaving treated areas cleaner and fresher.
It can be used as a general purpose cleaner to remove oil and grease deposits. First of all flush the system with cold water to prevent evaporation rates and polymerization then the most economical method of using RXSOL-22-2015-220 is by direct injection followed by recirculation washing, using tank cleaning machines. Spraying Method - Using LAC as delivered in drums, spray onto areas where residue remains following rough washing leave for 10-45 minutes (but do not allow to dry), then butterworth at maximum pressure and warm water 60oC for at least 3 hours, checking that there is no foam remaining in the final stages. Inspects tanks(s) and if desired result has been achieved fresh water rinse and dry.
** Make sure to take all safety precautions are followed when handling / spraying RXSOL-22-2015-220
Injection Method – not applicable.
Vegetable and Animal Oils (Cleaning Procedure)
For effective cleaning of animal and vegetable oils the first cleaning step is of utmost importance. Vegetable oils are divided in:
- Non-drying products
- Semi-drying products
- Drying products
- Fatty acids Non Drying Products
1. Pre-Cleaning: Remove all loose cargo residues, dust and solid debris from the cargo hold by sweeping, scraping or high-pressure water washing. Where possible, pre-rinse the surfaces with fresh water to remove loose contamination.
2. Preparation of Cleaning Solution: Dilute the Liquid Alkaline Cleaner with fresh water according to the degree of contamination. A 5-10% solution is suitable for general cleaning. For heavy oil, grease or stubborn cargo residues, the concentration may be increased as required after checking surface compatibility.
3. Application: Apply the prepared solution evenly over the contaminated surfaces using a low-pressure spray, foam applicator, chemical injection system or suitable cleaning equipment. Begin application from the lower sections and work upwards to ensure uniform coverage and reduce streaking.
4. Contact Time: Allow the cleaning solution to remain on the surface for approximately 15-30 minutes. For heavy contamination, a longer contact time may be required. Do not allow the cleaning solution to dry on the surface.
5. Agitation: Where deposits are particularly stubborn, agitate the treated areas using suitable brushes, deck scrubbers or high-pressure washing equipment to improve penetration and removal.
6. Final Washing: Wash the treated surfaces thoroughly with high-pressure fresh water, preferably working systematically from the upper sections downward. Continue rinsing until all loosened residues, cleaner and foam have been completely removed.
7. Inspection & Repeat Treatment: Inspect the hold after rinsing. Areas with remaining contamination may be spot-treated with a stronger solution, allowed suitable contact time and washed again.
Important: Before full-scale application, test the product on a small area to confirm compatibility with hold coatings, aluminium, galvanized surfaces and other sensitive materials. Collect and dispose of cleaning effluent in accordance with applicable vessel, port and environmental requirements.
-
Removes grease, oil, carbon deposits, soil and grime.
-
Keeps loosened deposits in suspension preventing re-deposition.
-
Low toxic. , Non-flammable.
-
Free from hydrocarbon solvents.
-
Effective and economical in use , Water-based cleaner.
-
RXSOL-22-2015-220 has numerous cleaning applications including removal of greases, waxes,
-
oil, sludge, soot, carbon deposits and general dirt and grime.
-
Non-corrosive to ferrous metals. Suitable for all tank-coatings.
-
Can be used for gas and hydrocarbon freeing of tanks.
-
Can be used for deodorizing
- Contains wetting agents.
NOTE : Acts as an acid-neutralizing agent.
If cargo / tank is not suitable to use alkaline cleaner then substitute of this product is Neutral Based cleaner i.e HCF Remover HD 210 Ltr
| Product Name | RXSOL-22-2015-220 |
| Product Type | Alkaclean HD |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
Stock Point : Mumbai, Kandla, Kolkata, Chennai, Visakhapatnam, Fujairah, Muscat, Nairobi
| Phone | +91 22 27815540-43 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| 123@rxmarine.com |
Alkaline cleaner Declaration according to recommendation 89/542/EEG.
|
Blend of SURFACTANT ANIONIC NON-IONIC, LAB |
Proprietory Blend |
40-50 |
| Butoxydiglycol | 112-34-5 | 1-5 |
|
Sodium Nitrite |
7632-00-0 |
0.1-1 |
|
C9-11 Pareth-6 |
68439-46-3 | 1-5 |
|
Butoxyethanol |
111-76-2 |
1-5 |
| Sodium Xylenesulfonate | 1300-72-7 | 1-5 |
| Sodium Hydroxide | 1310-73-2 | 1-5 |
| Tetrasodium EDTA | 64-02-8 | 0.1-1 |
| CI 15620 | 1658-56-6 |
0.1 |
|
Environmental Hazards |
None |
|
Human Health Hazards |
Moderates |
R 35:Causes skin burning effects
|
Inhalatin |
Move to fresh air and seek medical advice attention. |
|
Skin Contact |
Rinse with running water and soap. Skin care. Remove contaminated clothes. |
|
Eye Contact |
Flush with running water for at least 15 minutes Immediately . |
|
Ingestion |
Vomiting is dangerous , seek medical attention. |
Non Combustible Porduct
|
Suitable |
N.A. can use foam dry Co2 , water-spray. |
|
Not suitable |
Not applicable |
|
Special |
Not applicable |
|
Protection of fire Fighter |
Not applicable |
Special protective equipment for fire-fighters: Wear protective equipment.
|
Enviromentel Precaution |
Direct flow into drainage system, surface or ground water is prohibited. |
|
Cleaning Method |
Flush Spill Area with Water and remove with liquid-absorbing material like foam sand,sawdust etc.. |
|
Condition to Avoid |
Non flammable but avoid direct heating |
|
Materials to Avoid |
Do not subject to Acidic / Oxidizing Agents |
|
Handling |
Keep Container Tightly Closed |
Note:Eyewash facilities require at workplace The product causes corrosion on skin and mucous membranes Pl. Note that In case of discharge of acidic or alkaline products into the sewerage system the pH must be in the range of 6-10 since higher or lower pH values may damage the sewerage system or impair biological dosage treatment plants. So that for maintaining pH we have to add acidic / basic medium neutaliser . For example if pH is less than 6 basic neutraliser is required and if pH is more than 10 acidic nature neutraliser is required. For details of any guideline pl. Visit our technical website www.rxmarine.com
Dilute in water (always use plastic jar and RXSOL should be added to water never add water to RXSOL.)
Personal protection :
|
Respiratory System Protection |
Approved respirator must be worn when spraying |
|
Eye Protection |
Cear eye protection (on possibility of contact ) |
|
Hand protection |
Cear PVC chemical resistance protective glove |
Product Properties:
|
Appearance |
Slight Yellow - clear liquid |
|
Density |
In g/cm3 at 20°C: 1.21 |
|
Compatibility |
|
|
Metal |
No known effect |
|
Rubber |
No known effect |
|
pH |
Alkaline ( 13 ) |
|
Flash point |
Not Applicable |
|
Solubility |
100% soluble in water |
|
Packaging |
Size (in Litres)220 Ltrs |
|
Hazardous Decomposition Products |
Do not occur if stored and used as directed. n FIRE combustion CO, CO2 , NH3 , SOX etc hazardous gas produced |
NOTE : Avoid Contact With Acid
Comment - Not applicable , 100% Soluble in water
95 % added surfactants are biodegradable as per by international regulation .This material must be disposed with local national regulations.
As per guide line of local rules and regulation and before disposal and neutralization pl. refer 07 article.
| Proper Shipping Name | ||||
| UN | ||||
| Proper Shipping Name |
Alkaline Solution |
|||
| UNNo. | 1824 | |||
| Hazard Class | 8 | PackingGroup | II | |
| Road/Rail(ADR/RID) | ||||
| Proper Shipping Name |
Alkaline solution |
|||
| ADR UN No. | 1824 | |||
| ADR Hazard Class | 8 | Tremcard |
80S1824 |
|
|
Sea(IMDG) |
||||
| Proper Shipping Name |
Alkaline solution |
|||
| IMDG UN No. | 1824 | |||
| IMDG Hazard Class. | 8 | IMDG Pack Group. | II | |
| IMDG EmS | F-A, S-A | IMDG subrisk |
N/A |
|
| IMDG Labels |
8 |
IMDG Flash point |
N/A |
|
|
Air(ICAO/IATA) |
||||
| Proper Shipping Name |
Alkaline solution |
|||
| ICAO Un No. | 1824 | |||
| ICAO Hazard Class | 8 | ICAO Packing Group. | II | |
| ICAO subrisk |
N/A |
ICAO Labels |
8, CAO |
|
| ICAO Flashpoint | N/A | |||
|
DOT/ CFR (US Department of Transportation) |
||||
| DOT Proper Shipping Name |
Alkaline solution |
|||
| Hazardous Material |
Sodium hydroxide |
|||
| Hazard Class | 8 | Identification Number | UN 1824 | |
| Product RQ (lbs) | 3640 | DOT subrisk | N/A | |
| DOT Labels | 8 | DOTFlashpoint |
N/A |
|
Classification and labelling according to Chemicals Hazard Information and Packaging Regulations (CHIP). Symbols of danger :- C Corrosive
|
R phrases |
R 35 : Causes severe burns |
|
S-phrases |
S2: Keep out of reach of children S26 :In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. S28 : After contact with skin, wash immediately with plenty of water. S37/39 : Wear suitable gloves and eye/face protection. |
This information is based on our current level of knowledge and relates to the product in the state in which it is delivered. It is intended to describe our product from the point of view of safety requirements and is not intended to guarantee any particular propertie
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.