Accumulation of dust from this cargo on deck or in proximity to cargo spaces shall be removed as quickly as possible. Consideration shall be given to carefully cleaning exposed radio communications equipment to which dust might adhere, such as radar, radio, aerials, vhf installations, AIS and GPS. Hosing with sea water should be avoided.
HBI CARGO Hold Wash Concentrate RX is a versatile all-purpose QUALITY marine cleaning solution. It can be used as a powerful stand-alone cleaner for HBI CARGO . it can be used as a powerful\ stand alone cleaner for HBI CARGO dust and deposition .
FEATURES & BENEFITS :-------------------
$ Heavy duty HBI CARGO remover action
$ Can be diluted to suit cleaning needs
$ Environmentally friendly
$ Safe to use in occupied / covered areas
$ Reduces turnaround times
$ Can be easily applied by ship's crew
$ using an RXSOL Application Set
Features & Benefit:-
- Heavy duty HBI CARGO cleaning power
- Can be diluted to suit cleaning needs
- Environmentally friendly
- Safe to use onto the occupied areas /covered areas
- Reduces the turnaround times
- Cam be easily applied by ship’s crew
HBI at Elevated Temperatures
The Master of the ship must notify the port authorities if hydrogen gas is detected in the ship holds or if abnormal temperatures are measured in the HBI cargo holds. The Harbor Master and qualified personnel are responsible for executing the action plan when a ship or barge arrives with HBI at the following temperature levels:
A. Greater Than 65° Celsius but Less Than or Equal to 80° Celsius
Proceed with the following actions:
1 > Before unloading the vessel, measure the HBI temperature in each hold and record the measurements in the temperature log book.
2 > Unload the holds in the assigned zone and immediately transfer the HBI to the storage yard zone as described in PART II, Section 5.4 of this guide.
B. Temperature Greater Than 80° Celsius and Less Than or Equal to 150°
Celsius
Proceed with the following actions:
1 > Before unloading the vessel, measure the HBI temperature in each hold and record the measurements in the temperature log book. This should be done every two hours while the contingency is in effect.
2 > Unload the holds with HBI at temperature less than 65º Celsius first, then those containing HBI between 65º and 100º Celsius. Continue unloading HBI with temperatures between 100º and 150º Celsius in the
first transfer station, using the movement sense of the belt as a
reference.
3 > Transfer the HBI from the unloading zone clean and free of debris and flammable material, such as coal, coke and wood to the storage yard indicated by the client as follows:
Transfer the HBI during a maximum of three-minute intervals, and dose (i.e., mix the hotter with the cooler material to have an average temperature lower than the hottest one – no water to be used) the HBI that is at temperatures between 100° and 150° Celsius with cooler material for a maximum of two minutes. Stop the vibrating feeders for about five minutes, but keep the conveyor belts in motion. Repeat these steps until finished with HBI removal. While transferring the HBI, inspect the belt transfer system for any sign of overheating. In case of belt overheating, stop the HBI dosing and transfer but keep the transfer belts in motion until they cool. Take special care to avoid pouring water into hoppers and other equipment. Use a front-end loader to spread the HBI to a level of approximate 30 centimeter height to stop the reoxidation, Verify that the belts are cooled down and resume HBI transfer per
the previous instructions.
C . Greater than 150° Celsius
Proceed with the following actions:
1 > Before unloading the holds, measure the HBI temperature in each hold and record the measurements in the temperature log book. This should be done every two hours while the contingency is in effect.
2 > Position the HBI with temperatures greater than 150° Celsius at the end of the reception area and spray with pressurized water. In this case, there is no option but to momentarily cool down the HBI.
3 > When the temperature is reduced to between 80º and 150° Celsius proceed with the steps described in 6.3.2.2. Caution: Do not spray water on hot HBI that is steaming (i.e., emitting water vapor).
Procedure If Hydrogen Concentration Is Over 1% (25% LEL)
1 > Inform the shipper immediately and seek expert advice.
2 > Keep the natural surface ventilation open at all times
3 > Monitor LEL in the holds continuously until level drops to less than 25 %.
4 > Avoid any possible ignition source on the vicinity.
5 > Care shall be taken as to prevent any spark generation.
6 > Monitor the hydrogen concentration in the holds and keep the surface ventilation (either natural or mechanical) until values fall below 1%.
7 > When hydrogen levels are within safe values, proceed as normal.
8 > On the contrary, additional ventilation should be applied to the space if available and re-testing should be conducted after a suitable interval.
9 > Contact the P & I Club and Shipper and follow the instructions of the appointed expert or surveyor.
10 > At sea, do not open the troubled hold without explicit instructions from the shipper or appointed expert or surveyor.
11 > Ensure there are no possible sources of ignition near the cargo spaces, adjacent spaces or open decks.
25 / 210 Ltrs</p>
| Product Name | RXSOL-22-2216-210 |
| Product Type | HBI CARGO Hold Wash Concentrate RX |
Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA
| Phone | +91 22 65113333 / 5555 / 9999 / 27611360 |
| Fax | +91 22 2781 1318 :::AOH :0091 9821214367 |
| mail@rxmarine.com |
|
Chemical Name |
Concentration |
CAS Number |
EC Number |
R Phrases* |
Symbols |
|
Terpenes Hydrocarbons |
5-10 |
94266-47-4 |
NA |
10, 65 |
Xn |
|
Fatty alcohol ethoxylate |
5-10 |
34398-01-1 |
500-084-3 |
41 |
Xi |
|
Alkylglucoside ethoxylate |
1-5 |
161074-93-7 |
500-529-1 |
41 |
Xi |
|
2-(2-butoxyethoxy)ethanol |
1-5 |
112-34-5 |
203-961-6 |
36 |
Xi |
|
Alkylamine carboxylate |
1-5 |
3655-00-3 |
222-899-0 |
36 |
Xi |
*See Section 16
|
Odour |
Charcstatic |
|
Appearance |
Liquid, Clear, soluble in water |
|
Contact witheyes |
Causes severe irritation, Risk of serious damage to eyes (R41) |
|
Contact withskin |
Prolonged skin contact will result in defatting of the skin, leading to irritation, and in some cases, dermatitis |
|
Inhalation |
Mildly irritating to respiratory system |
|
Ingestion |
May cause gastro-intestinal disturbances |
|
Contact with skin |
Wash affected area with plenty of water Remove contaminated clothing Contaminated clothing should be laundered before reuse |
|
Contact with eyes |
If substance has got into eyes, immediately wash out with plenty of water for at least 15 minutes Irrigate eyes thoroughly whilst lifting eyelids Obtain immediate medical attention |
|
Ingestion |
Never make an unconscious person vomit or drink fluids Give 200-300mls (half pint) water to drink Seek medical attention if ill effects occur |
|
Inhalation |
Remove patient to fresh air When in doubt or symptoms persist, seek medical attention |
|
General |
In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible) (S45) |
- Not flammable. In case of fire use extinguishing media appropriate to surrounding conditions
|
Personal Precautions |
Wear protective clothing as per section 8 |
|
Environmental Precautions |
Do not allow to enter public sewers and watercourses |
|
Clean Up Actions |
Absorb spillage in inert material and shovel up Ventilate the area and wash spill site after material pick-up is complete |
|
Special Precautions |
Wear protective clothing as per section 8 |
|
Handling |
Wear protective clothing as per section 8 Avoid contact with skin and eyes (S24/25) Eyewash bottles should be available |
|
Storage |
Keep in a cool, well ventilated place (S3/9) Protect from frost. |
|
Exposure Limits |
No exposure limits have been set for this substance |
|
Exposure controls |
No special ventilation is required unless the product is used in a spray form |
|
Occupational exposure controls |
Wear suitable protective clothing, including eye/face protection and gloves (plastic or rubber are recommended) No respiratory protection is required unless subject to contact with substance mist During fumigation/spraying wear suitable respiratory equipment (S42) |
|
Odour |
Characstic |
|
Appearance |
Liquid, Clear / Pale yellow soluble in water |
|
pH |
11.5 |
|
Boiling point > |
100 °C at 760 mm /Hg |
|
Vapour pressure |
not known |
|
Vapour density |
not known |
|
Freezing point |
0 °C at 760 mm/Hg |
|
Completely soluble in water |
|
|
Specific gravity (water=1) |
1.0 |
- This article is considered stable under normal conditions
- Avoid overheating
|
Toxicological information |
No experimental data available |
|
Inhalation |
In cases of severe exposure, irritation may develop |
|
Contact with skin |
Prolonged skin contact will result in defatting of the skin, leading to irritation, and in some cases, dermatitis |
|
Contact with eyes |
May cause severe irritation Can cause damage to the eyes |
|
Ingestion |
No effects for small dosage. Large dose effects not known May cause gastro-intestinal disturbances |
|
Carcinogenicity |
No evidence of carcinogenic effects |
|
Ecotoxicity |
This product does not contain ingredients which are classified in the EU as dangerous for the environment. The product was found to meet the requirements of paragraph 1.8.2 of the P&A Standards and is included in MEPC.2/Circ.8 |
|
Mobility |
Completely soluble in water |
|
Persistence and Biodegradability |
The components in this product are readily biodegradable. |
|
Bioaccumulation Potential |
Bioaccumulation of the components in this product is insignificant. |
|
Other Adverse Effects |
No environmental problems are expected when the product is used / handled correctly. |
|
Classification |
EU Waste class: 07.06 |
|
Disposal considerations |
Do not discharge into drains or the environment, dispose to an authorised waste collection point Disposal should be in accordance with local, state or national legislation |
- Not classified as hazardous for transport
|
Risk Phrases |
Risk of serious damage to eyes (R41) |
|
Safety Phrases |
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice (S26) Wear suitable gloves and eye/face protection (S37/39) |
Text of R and S phrase codes used in this safety data sheet:-R10: Flammable; R36:Irritating to eyes; R41: Risk of serious damage to eyes; R65: Harmful: may cause lung damage if swallowed. The information provided about the product on this Safety Data Sheet has been compiled from knowledge of the individual constituents The data given here is based on current knowledge and experience. This Safety Data Sheet describes the product in terms of safety requirements and does not signify any warranty with regard to the product's properties The data given here only applies when product used for proper application(s). The product is not sold as suitable for other applications - usage in such may cause risks not mentioned in this sheet. Do not use for other application(s) without seeking advice from manufacturer Composition information in accordance with Regulation (EC) No 648/2004 of the European Parliament and of the Council of 31 March 2004 on detergents:
| Nonionic surfactants | 5-15 | % |
| Amphoteric surfactants | 5 | % |
| Terpenes Hydrocarbons | 5-15 | % |
DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.