RO Antiscalant 9005

High performance liquid antiscalant and dispersant for controlling inorganic scale formation and particulate fouling in Reverse Osmosis (RO) membrane systems.
Category

RXSOL RO Antiscalant 9005 – High Performance Reverse Osmosis Membrane Scale Inhibitor

Product Name: RXSOL RO Antiscalant 9005
Brand: RXSOL – RX Marine International
Product Category: Reverse Osmosis Chemicals / Membrane Scale Inhibitors / Water Treatment Chemicals
Application: Industrial RO Plants, Brackish Water RO, Seawater RO, Desalination Plants and Water Recycling Systems

Proposed RXSOL product designation. Product code and performance specifications require confirmation.

Product Description

RXSOL RO Antiscalant 9005 is a proposed high-performance liquid antiscalant and dispersant for controlling inorganic scale formation and particulate fouling in Reverse Osmosis (RO) membrane systems.

The product is intended to minimize the deposition of sparingly soluble salts, including calcium carbonate, calcium sulfate, barium sulfate and strontium sulfate, while assisting in the dispersion of suspended inorganic particles and metal oxide contaminants.

RXSOL RO Antiscalant 9005 is designed for use in industrial RO plants treating groundwater, surface water, brackish water, seawater and suitably pretreated industrial effluent.

Its proposed treatment approach combines scale inhibition, crystal growth modification and dispersant action to help maintain membrane cleanliness and reduce mineral scaling.

This product concept is based on the application profile of Thermax MAXTREAT 9005, which describes broad inorganic scale control and membrane dispersant performance.

Application

Applications of RXSOL RO Antiscalant 9005

1. Industrial Reverse Osmosis Plants

Intended to help prevent mineral scale accumulation on RO membrane surfaces in industrial water purification systems.

2. Brackish Water RO Systems

Designed for scale management in brackish groundwater treatment plants containing elevated concentrations of calcium, magnesium, sulfate and other dissolved minerals.

3. Seawater Desalination Plants

Suitable as a development candidate for seawater RO applications where high salinity and scaling potential require specialized chemical treatment.

4. Wastewater Recycling and Reuse

Can be evaluated for RO systems treating suitably pretreated industrial effluent, where variable water chemistry may increase scaling and particulate fouling risks.

5. Boiler Feedwater Preparation

Intended for RO pretreatment systems supplying purified water to industrial boilers and steam generation facilities.

6. Power Plants and Process Industries

Potential applications include RO systems in power generation, petrochemicals, refineries, manufacturing facilities and industrial utilities.

Mechanism of Action

RXSOL RO Antiscalant 9005 is intended to work through three principal mechanisms.

Threshold Inhibition: Antiscalant molecules interfere with the nucleation and growth of mineral scale, helping prevent precipitation at low treatment concentrations.

Crystal Modification: The formulation interferes with crystal development, reducing the tendency of scale-forming minerals to form adherent deposits.

Dispersion: Dispersant components help keep selected inorganic particles suspended in the flowing water, reducing their tendency to accumulate on membrane surfaces.

Dose

Recommended Dosage and Application

The Thermax MAXTREAT 9005 reference document recommends 1–6 ppm of neat product, with injection upstream of the cartridge filter.

For RXSOL product development, this range may be used as an initial performance-testing target, but it is not yet a validated RXSOL dosage.

Feedwater Condition

Dosing Recommendation

Low scaling potential

Establish through water analysis

Moderate scaling potential

Determine using scaling calculations

High hardness / sulfate concentration

Conduct detailed antiscalant evaluation

High silica concentration

Verify silica limits and treatment performance

High recovery RO system

Evaluate concentrated reject-water chemistry

Dosage Calculation

For a liquid product, when dosage is expressed in mg/L:

Dosing Rate (L/h) =     Q X D  / 1000 X Product Density

Where:

  • Q = RO feedwater flow in m³/h

  • D = required product dosage in mg/L

  • Product density in kg/L

RO Antiscalant Dosing Calculator


Antiscalant dosage = 3 mg/L
 


Then Neat product feed ::: 0.136 L/h

Neat product per day ::: 3.27 L

Illustrative calculation assuming continuous operation for 24 hours. Density of 1.10 kg/L is an example, not a measured RXSOL specification. Actual dosage must be established from feedwater analysis.

Application Procedure

  1. Analyze RO feedwater for calcium, magnesium, alkalinity, sulfate, silica, barium, strontium, iron, pH and total dissolved solids.

  2. Determine the intended membrane recovery rate and operating temperature.

  3. Calculate scaling potential at the concentrate end of the RO system.

  4. Select and validate the antiscalant dosage.

  5. Install the dosing system at a location that provides adequate mixing before the membranes.

  6. Monitor differential pressure, normalized permeate flow, salt rejection and cleaning frequency.

NOTE ::: Do not combine concentrated antiscalant directly with other treatment chemicals unless compatibility has been established.

Technical specifications

Technical Specifications

Parameter

Proposed RXSOL Description

Appearance

Liquid

Product Type

RO Membrane Antiscalant and Dispersant

Chemical Nature

Proprietary antiscalant blend; final composition to be established

Water Solubility

Intended to be fully water-miscible

Target Feedwater

Groundwater, surface water, brackish water and seawater

Target Operating pH

6–10, subject to validation

Calcium Carbonate Control

Target performance up to LSI +2.2, subject to testing

Recommended Dose

Preliminary evaluation range 1–6 ppm

Injection Point

Upstream of RO cartridge filtration, subject to system design

Packaging

Proposed 20 kg, 25 kg and 210 kg

Shelf Life

To be established by stability testing

Important: The pH range, LSI capability and 1–6 ppm dosage are reference performance characteristics from the Thermax MAXTREAT 9005 document, not verified RXSOL specifications.

 
ImImg

 

 

 

Storage and Handling

Store in tightly closed, chemically compatible containers away from direct sunlight and extreme temperatures. Protect the product from contamination.

Use suitable gloves and eye protection when handling concentrated treatment chemicals. Follow the actual RXSOL Safety Data Sheet once the commercial formulation has been finalized.

RXSOL RO Antiscalant Supplier in India, UAE and Oman

RXSOL supports industrial water treatment chemical enquiries across major industrial and marine markets.

India: Mumbai, Navi Mumbai, Kolkata, Chennai, Visakhapatnam, Kakinada, Ahmedabad, Surat, Jamnagar, Kandla, Mundra, Paradip and other industrial locations.

United Arab Emirates: Dubai, Abu Dhabi, Sharjah, Ajman, Fujairah, Jebel Ali, Musaffah and Ruwais.

Oman: Muscat, Sohar, Salalah, Duqm, Sur and other industrial locations.

Product availability, packaging and delivery arrangements are subject to confirmation.

Note

Scale Deposits Targeted

Scale or Deposit

Intended Treatment Function

Calcium Carbonate (CaCO₃)

Threshold scale inhibition

Calcium Sulfate (CaSO₄)

Crystal growth inhibition

Barium Sulfate (BaSO₄)

Scale formation control

Strontium Sulfate (SrSO₄)

Scale inhibition

Silica (SiO₂)

Scale management and dispersion

Iron Oxides

Particulate dispersion

Other Metal Oxides

Fouling reduction through dispersion

Actual performance must be established using the selected formulation, feedwater analysis and membrane operating conditions.

Remarks / Precaution

Frequently Asked Questions

Q1. What is RXSOL RO Antiscalant 9005?

It is a proposed liquid antiscalant and dispersant intended for controlling inorganic scale formation in Reverse Osmosis membrane systems.

Q2. What types of scale can RO antiscalants control?

Appropriately formulated antiscalants can inhibit calcium carbonate, calcium sulfate, barium sulfate and strontium sulfate. Silica control requires additional formulation-specific validation.

Q3. What is the recommended dosage?

The reference product uses 1–6 ppm. The final RXSOL dosage must be determined through feedwater analysis and product performance testing.

Q4. Where should antiscalant be injected?

Normally into the RO feedwater line before the membrane system, at a point allowing adequate mixing and consistent chemical distribution.

Q5. Can the product be used in seawater RO plants?

A suitable antiscalant can be used in seawater RO systems, but membrane compatibility, salinity and scaling performance must be verified for the final formulation.

Q6. Does antiscalant remove existing membrane scale?

No. Antiscalants are primarily preventive chemicals. Existing deposits generally require an appropriate membrane-cleaning procedure.

MSDS
 

 

Product Name

Latex Emulsion PRIMER

Product Type RXSOL-41-9005-025

 

Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA

 

Phone +91 22 65113333 / 27611360 / 27815540
Fax +91 22 2781 1318 :::AOH :0091 9322594669
Email mail@rxmarine.com

 

Non-hazardous:
Pigmented Latex emulsion coating comprised of water, pigments, fillers, additives,
and latex emulsion resin.

Hazardous:
Chemical Name           CAS No.         Percent           Exposure Limits

1 - Titanium dioxide  13463-67-7        25.0                ACGIH TLV
                                                                                         10 mg/m3 as Dust
                                                                                                OSHA PEL
                                                                                  10 mg/m3 as Total Dust
                                                                                  5 mg/m3 Respirable Fraction
2 - Ethylene glycol   107-21-1          5.0                    OSHA PEL
                                                                 50 ppm
Note: Normal application procedures pose no hazard since titanium dioxide is wetted and encapsulated, but grinding or sanding dried films of this product may yield respirable titanium dioxide dust. Control exposures to less than 0.1 mg/m3 using NIOSH/MSHA-approved dust filter respirators.
 

Note: Per 29CFR 1910.1200 (g) (2) (1) (C) (2), only hazardous substances present in excess of 1.0% by weight (or 0.1% for carcinogens) must be listed on an MSDS.

 

Emergency Overview:

Product Description: This product is a pigmented liquid.

Health Hazards:

Eyes: May cause slight irritation.

Skin: Substance may cause slight skin irritation.

Inhalation: May cause irritation of respiratory tract.

Ingestion: Ingestion may cause gastrointestinal irritation, nausea, and vomitting.

Flammability Hazards: This product is not flammable. If this product is involved in a fire, the decomposition products generated will include irritating vapors and gases and some carbon monoxide.

Reactivity Hazards: This product is not reactive.

Environmental Hazards: Although release of this product to the environment is not expected to cause significant adverse effect, all releases should be avoided.

Eyes: Immediately flush eyes with plenty of water for at least 15 minutes and consult physician.

Skin: Wash skin thoroughly with soap and water. If drenched with product, remove and wash clothing before reuse.

Ingestion: Ingestion If victim is conscious give 2 glasses of water. Call a physician.

Inhalation: N/A

Product is non-combustible.

Flash point:                 Autoignition Temperature:
F: Not flammable         F: Not Established
C: Not flammable         C: Not Established


Extinguishing Media:

Use extinguishing media appropriate for surrounding fire

Water Spray:OK
Carbon Dioxide :OK
Foam : OK
Dry Chemical : OK
Halon : OK
Other :Any “ABC” Class

 

Accidental Release Measures:

Personal Precautions: Do not get in eyes. Do not take internally. Avoid skin contact. Prevent prolonged or repeated breathing of vapor or spray mists. Keep unnecessary people away. Floor may be slippery, use care to avoid falling. Ventilate the area. Remove with inert absorbent.

Environmental Precautions: Keep spills and cleaning run-offs out of municipal sewers and open bodies of water. Comply with local, state and national regulations.

Handling and Storage:

Storage: Store in a cool, dry place

Keep closure tight and containers upright to prevent leakage.

Precautionary labeling: “KEEP FROM FREEZING”.

Precautions: Use only with adequate ventilation. Avoid contact with skin and eyes. Avoid breathing vapor and spray mist. Wash hands after using.

This coating may contain materials classified as nuisance particulates (listed “as Dust” in Section 2) which may be present at hazardous levels only during the sanding or abrading of the dried film. If no specific dusts are listed in Section 2, the applicable limits for nuisance dusts are ACGIH TLV 10 mg/m3 (total dust), 3 mg/ m3 (respirable fraction), OSHA PEL 10 mg/m3 (total dust), 5 mg/m3 (respirable fraction).

Work Hygienic Practices: Avoid contact with skin. Do not get in eyes. Do not take internally. Avoid breathing vapors or spray mists.

Ventilation: Use in well-ventilated areas. General exhaust acceptable if the exposure to materials in Section 2 is maintained below applicable exposure limits.

Refer to OSHA Standards 1910.94, 1910.107, 1910.108.

Respiratory Protection: If personal exposure cannot be controlled below applicable limits by ventilation, wear a properly fitted organic vapor/particulate respirator approved by NIOSH/MSHA for protection against materials in Section 2.

When sanding or abrading the dried film, wear a dust/mist respirator approved by NIOSH/MSHA for dust which may be generated from this product, underlying  paint, or the abrasive.

Eye Protection: Use approved safety eyewear including side shields, chemical goggles or face shields.

Skin Protection: Wear neoprene or rubber gloves to prevent skin contact if prolonged skin contact is likely. Wash hands before eating, smoking or using the wash room.

 

Appearance:  

Viscous liquid

Viscosity @ 77°F:

80 Kreb Units ± 5.0

Odor:

Slight odor

Percent Solids By Weight:

49.1% ± 2.0

Boiling Point:

212°F

Solubility in Water:

Total

Freezing Point:

32°F

Vapor Density @ 68°F:

Heavier than air

Vapor Pressure (mmHg) @ 68°F:

17

Specific Gravity (H2O = 1) @ 68°F:

1.3 lbs/gal ± 0.5

Weight Per Gallon:

10.6 lbs/gal ± 0.5

Specific Gravity (H2O = 1) @ 68°F:

Slower than ether

 

Stability: Stable

Incompatibility: (Material to Avoid): Avoid contact with strong oxidizing agents (e.g. nitric acid, permanganates), etc.

Hazardous Decomposition or By-Products: Some carbon monoxide.

Hazardous Polymerization: Will not occur. 

Toxicological Information: Chronic Health Hazards IARC’s Monograph No. 93 reports there is sufficient evidence of carcinogenicity in experimental rats exposed to titanium dioxide but inadequate evidence for carcinogenicity in humans and has assigned a Group 2B rating. In addition, the IARC summary concludes, “No significant exposure to titanium dioxide is thought to occur during the use of products in which titanium is bound to other materials, such as paint.”

Toxicology Data

Chemical Name                                         CAS No.                                    LD50

Titanium dioxide                                   13463-67-7 Oral:                  >24000 mg/kg (Rat)

                                                                                                          Dermal: >10000 mg/m3 (rabbit)

                                                                                                          Inhalation (Dust): >6.82 mg/L (Rat, 4hr.)

Ethylene glycol                                      107 -21-1                             Oral: 8.54 g/kg (Rat)

Ecological Information:

Well-diluted product will have no environmental consequences. Less than 5% Ethylene glycol present in this product yields the following environmental considerations: Ethylene glycol is 100% volatile. Once volatilized it will react in the atmosphere with hydroxyl radicals with a half-life on about 1 day. For accidental spills, note that Ethylene glycol in typical river water at 20°C was found to completely degrade in 3 days. At temperatures of 8°C, degradation occurred in 7 days. Toxicity to fish: LD50 Carrasisus auratus (goldfish) greater than 5,000 gl/L/24 hour. Modified ASTM D 1345. Algea:(Chlorella pyrenoidosa) 180,000 mg/L toxic.

Waste Disposal Method:

Waste from this product is not hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261. If incinerating, do so in an approved facility, and do not incinerate closed container. Dispose of in accordance with Federal, State/Provincial, and Local regulations regarding pollution.

U.S. Department of Transportation

Proper Shipping Name: Non-Hazardous Water-Based Paint

Hazard Class: “Not Regulated”

Label Statement: “Keep From Freezing”

Class 55 Non-Hazardous Water-Based Paint

Canada (TDG)

Not Regulated for Transportation.

IMO

Not Regulated for Transportation.

U.S. Federal Regulations:

TSCA (TOXIC SUBSTANCE CONTROL ACT): All components of this product are in compliance with the inventory listing requirements of the U.S. Toxic Substances Control Act (TSCA) Chemical Substance Inventory.

CERCLA (COMPREHENSIVE RESPONSE COMPENSATION, AND LIABILIT

 

Product Name

Latex Emulsion PRIMER

Product Type RXSOL-41-9005-025

 

Company Details:
RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA

 

Phone +91 22 65113333 / 27611360 / 27815540
Fax +91 22 2781 1318 :::AOH :0091 9322594669
Email mail@rxmarine.com

 

Non-hazardous:
Pigmented Latex emulsion coating comprised of water, pigments, fillers, additives,
and latex emulsion resin.

Hazardous:
Chemical Name           CAS No.         Percent           Exposure Limits

1 - Titanium dioxide  13463-67-7        25.0                ACGIH TLV
                                                                                         10 mg/m3 as Dust
                                                                                                OSHA PEL
                                                                                  10 mg/m3 as Total Dust
                                                                                  5 mg/m3 Respirable Fraction
2 - Ethylene glycol   107-21-1          5.0                    OSHA PEL
                                                                 50 ppm
Note: Normal application procedures pose no hazard since titanium dioxide is wetted and encapsulated, but grinding or sanding dried films of this product may yield respirable titanium dioxide dust. Control exposures to less than 0.1 mg/m3 using NIOSH/MSHA-approved dust filter respirators.
 

Note: Per 29CFR 1910.1200 (g) (2) (1) (C) (2), only hazardous substances present in excess of 1.0% by weight (or 0.1% for carcinogens) must be listed on an MSDS.

 

Emergency Overview:

Product Description: This product is a pigmented liquid.

Health Hazards:

Eyes: May cause slight irritation.

Skin: Substance may cause slight skin irritation.

Inhalation: May cause irritation of respiratory tract.

Ingestion: Ingestion may cause gastrointestinal irritation, nausea, and vomitting.

Flammability Hazards: This product is not flammable. If this product is involved in a fire, the decomposition products generated will include irritating vapors and gases and some carbon monoxide.

Reactivity Hazards: This product is not reactive.

Environmental Hazards: Although release of this product to the environment is not expected to cause significant adverse effect, all releases should be avoided.

Eyes: Immediately flush eyes with plenty of water for at least 15 minutes and consult physician.

Skin: Wash skin thoroughly with soap and water. If drenched with product, remove and wash clothing before reuse.

Ingestion: Ingestion If victim is conscious give 2 glasses of water. Call a physician.

Inhalation: N/A

Product is non-combustible.

Flash point:                 Autoignition Temperature:
F: Not flammable         F: Not Established
C: Not flammable         C: Not Established


Extinguishing Media:

Use extinguishing media appropriate for surrounding fire

Water Spray:OK
Carbon Dioxide :OK
Foam : OK
Dry Chemical : OK
Halon : OK
Other :Any “ABC” Class

 

Accidental Release Measures:

Personal Precautions: Do not get in eyes. Do not take internally. Avoid skin contact. Prevent prolonged or repeated breathing of vapor or spray mists. Keep unnecessary people away. Floor may be slippery, use care to avoid falling. Ventilate the area. Remove with inert absorbent.

Environmental Precautions: Keep spills and cleaning run-offs out of municipal sewers and open bodies of water. Comply with local, state and national regulations.

Handling and Storage:

Storage: Store in a cool, dry place

Keep closure tight and containers upright to prevent leakage.

Precautionary labeling: “KEEP FROM FREEZING”.

Precautions: Use only with adequate ventilation. Avoid contact with skin and eyes. Avoid breathing vapor and spray mist. Wash hands after using.

This coating may contain materials classified as nuisance particulates (listed “as Dust” in Section 2) which may be present at hazardous levels only during the sanding or abrading of the dried film. If no specific dusts are listed in Section 2, the applicable limits for nuisance dusts are ACGIH TLV 10 mg/m3 (total dust), 3 mg/ m3 (respirable fraction), OSHA PEL 10 mg/m3 (total dust), 5 mg/m3 (respirable fraction).

Work Hygienic Practices: Avoid contact with skin. Do not get in eyes. Do not take internally. Avoid breathing vapors or spray mists.

Ventilation: Use in well-ventilated areas. General exhaust acceptable if the exposure to materials in Section 2 is maintained below applicable exposure limits.

Refer to OSHA Standards 1910.94, 1910.107, 1910.108.

Respiratory Protection: If personal exposure cannot be controlled below applicable limits by ventilation, wear a properly fitted organic vapor/particulate respirator approved by NIOSH/MSHA for protection against materials in Section 2.

When sanding or abrading the dried film, wear a dust/mist respirator approved by NIOSH/MSHA for dust which may be generated from this product, underlying  paint, or the abrasive.

Eye Protection: Use approved safety eyewear including side shields, chemical goggles or face shields.

Skin Protection: Wear neoprene or rubber gloves to prevent skin contact if prolonged skin contact is likely. Wash hands before eating, smoking or using the wash room.

 

Appearance:  

Viscous liquid

Viscosity @ 77°F:

80 Kreb Units ± 5.0

Odor:

Slight odor

Percent Solids By Weight:

49.1% ± 2.0

Boiling Point:

212°F

Solubility in Water:

Total

Freezing Point:

32°F

Vapor Density @ 68°F:

Heavier than air

Vapor Pressure (mmHg) @ 68°F:

17

Specific Gravity (H2O = 1) @ 68°F:

1.3 lbs/gal ± 0.5

Weight Per Gallon:

10.6 lbs/gal ± 0.5

Specific Gravity (H2O = 1) @ 68°F:

Slower than ether

 

Stability: Stable

Incompatibility: (Material to Avoid): Avoid contact with strong oxidizing agents (e.g. nitric acid, permanganates), etc.

Hazardous Decomposition or By-Products: Some carbon monoxide.

Hazardous Polymerization: Will not occur. 

Toxicological Information: Chronic Health Hazards IARC’s Monograph No. 93 reports there is sufficient evidence of carcinogenicity in experimental rats exposed to titanium dioxide but inadequate evidence for carcinogenicity in humans and has assigned a Group 2B rating. In addition, the IARC summary concludes, “No significant exposure to titanium dioxide is thought to occur during the use of products in which titanium is bound to other materials, such as paint.”

Toxicology Data

Chemical Name                                         CAS No.                                    LD50

Titanium dioxide                                   13463-67-7 Oral:                  >24000 mg/kg (Rat)

                                                                                                          Dermal: >10000 mg/m3 (rabbit)

                                                                                                          Inhalation (Dust): >6.82 mg/L (Rat, 4hr.)

Ethylene glycol                                      107 -21-1                             Oral: 8.54 g/kg (Rat)

Ecological Information:

Well-diluted product will have no environmental consequences. Less than 5% Ethylene glycol present in this product yields the following environmental considerations: Ethylene glycol is 100% volatile. Once volatilized it will react in the atmosphere with hydroxyl radicals with a half-life on about 1 day. For accidental spills, note that Ethylene glycol in typical river water at 20°C was found to completely degrade in 3 days. At temperatures of 8°C, degradation occurred in 7 days. Toxicity to fish: LD50 Carrasisus auratus (goldfish) greater than 5,000 gl/L/24 hour. Modified ASTM D 1345. Algea:(Chlorella pyrenoidosa) 180,000 mg/L toxic.

Waste Disposal Method:

Waste from this product is not hazardous as defined under the Resource Conservation and Recovery Act (RCRA) 40 CFR 261. If incinerating, do so in an approved facility, and do not incinerate closed container. Dispose of in accordance with Federal, State/Provincial, and Local regulations regarding pollution.

U.S. Department of Transportation

Proper Shipping Name: Non-Hazardous Water-Based Paint

Hazard Class: “Not Regulated”

Label Statement: “Keep From Freezing”

Class 55 Non-Hazardous Water-Based Paint

Canada (TDG)

Not Regulated for Transportation.

IMO

Not Regulated for Transportation.

U.S. Federal Regulations:

TSCA (TOXIC SUBSTANCE CONTROL ACT): All components of this product are in compliance with the inventory listing requirements of the U.S. Toxic Substances Control Act (TSCA) Chemical Substance Inventory.

CERCLA (COMPREHENSIVE RESPONSE COMPENSATION, AND LIABILITY

Need a quote for this product?

Tell us the grade, packing and quantity you need — we ship across India and to major ports.

Request a quote WhatsApp +91 87529 36666 mumbaichems @ gmail.com