RXSOL Gold Industrial Cleaner is a biodegradable concentrate Liquid used for cleaning and degreasing parts and equipment. This single solution, used in varying concentrations with water, can replace half a dozen or more other products, many of them hazardous and expensive, which must ordinarily be kept on hand in large shops.
RXSOL Gold Industrial Cleaner is non-toxic, non-flammable and non-corrosive. It's rust inhibitive, stable in long-time storage, and is not damaged by freezing.Futhermore, RXSOL Gold Industrial Cleaner meets all OSHA requirements and conforms to the most rigid safety and performance standards set by leading industries.
RXSOL Gold Industrial Cleaner helps to keep the equipment clean and corrosion free, eliminating lime and particle build-up on heating coils. Since RXSOL Gold Industrial Cleaner does not react with the oils it removes, the product can be recycled again and again through filtration systems with little or no loss in efficiency. RXSOL Gold Industrial Cleaner disperses oils so there is no sludge build-up. When the agitation system is turned off, oils rise to the surface and can be easily removed, while particulate matter settles to the bottom leaving the solution clean and virtually new.
RXSOL Gold Industrial Cleaner can be used in a variety of application methods and is safe for both ferrous and non-ferrous metals, does not harm painted surfaces, natural rubber, electric wiring insulation, leather, carpet, silicon rubber, neoprene or polypropylene.
Heated Dip Tanks:
RXSOL Gold Industrial Cleaner should be used at a 1 part BGIC to 20 parts water concentration and heated to 140 degrees F. RXSOL Gold Industrial Cleanercan replace chlorinated hydrocarbons in vapor degreaser tanks with minor modifications. Vapor tanks can be easily and economically converted to a submersion system with the addition of a source of agitation. It is recommended that 60% of the tank volume per minute be moved in order to provide the best agitation. Air agitation is NOT recommended.
Ultra-sonics:
RXSOL Gold Industrial Cleaner in a 5% concentration is a perfect cleaner to use in ultrasonic tanks. The tank should be heated to 140 degrees F. Parts washed in Blue Gold and thoroughly dried are protected from surface rusting for approximately 7 to 15 days. These parts can then be painted, welded or bonded with no further treatment.
High Pressure Sprayers & Steam Cleaners:
RXSOL Gold Industrial Cleaner is ideal for high pressure and steam cleaning applications. It keeps every part of the system clean and free of corrosion, thus reducing maintenance and down time. In application tests, it has been shown that the higher the pressure the lighter the concentration needed for effective cleaning. The following is a suggestion on various concentrations based on the pressure (psi).
| Pressure | Water Temperature | Dilution |
| 150-300 PSI | Cold | 1-50 |
| 100 deg. F.- 130 deg. F. | 1-100 | |
| 500-800 PSI | Cold | 1-100 |
| 100 deg. F-130 deg. F. | 1-250 | |
| 1000 PSI | Cold | 1-200 |
| 100 deg. F.- 130 deg. F. | 1-400 |
Hand wiping
RXSOL Gold Industrial Cleaner is safe enough to use in hand wiping applications. We suggest however, if prolonged use is necessary that you use gloves as the Blue Gold will take the oils out of your hands. (Most of the compressed gas applications and oxygen related cleaning applications are accomplished with hand wiping.)
Physical State : Liquid
Appearance : Blue
Spec Gravity: 1.01
PH: 13.0
Solubility in Water: Complete
Safety :
RXSOL Gold Industrial Cleaner is not corrosive, flammable or toxic (either through vapor inhalation, skin contact or ingestion). All ingredients in Blue Gold are on the TSCA inventory list and RXSOL Gold has no B.O.D. (biological oxygen demand) and very low V.O.C. (volatile organic compound is .5% in a .5% solution).

| Product Name | RXSOL-19-1213-500 |
| Product Type | RXSOL GOLD Industrial Cleaner 5 Ltr |
Company Details:
RX MARINE INTERNATIONAL
105, A wing, BSEL, TECH PARK.
VASHI, NEW BOMBAY 400703 INDIA
Stock Point: Mumbai, Kandla, Kolkata, Chennai, Vizag, Fujairah, Muscat, Nairobi
| Phone | +91 22 65113333/5555/9999/27611360/27815540 |
| Fax | +91 22 2781 1318 ::: AOH: 0091 9322594669 |
| mail@rxmarine.com |

| Ingredient | CAS No. | % (w/w) |
| 2-(2-Butoxyethoxy)ethanol (Diethylene Glycol Monobutyl Ether) | 112-34-5 | 7-10% |
| Sodium Metasilicate Pentahydrate (Disodium Trioxosilicate) | 10213-79-3 | 4-9% |
| Nonylphenol Ethoxylate (Nonylphenyl-polyethylene glycol) | 9016-45-9 | 1-5% |
| Exact percentages within the listed ranges have been withheld as a trade secret. | ||

Signal word: Danger.
Hazard classification: Skin irritation Category 2; serious eye damage Category 1; acute toxicity Category 3 as stated in the source SDS.
Hazard statements: H315 Causes skin irritation. H318 Causes serious eye damage. H402 Harmful to aquatic life. Harmful if swallowed. Spray mist may irritate the respiratory tract.
Precautionary statements: P261 Avoid breathing dust/fume/gas/mist/vapours/spray. P262 Do not get in eyes, on skin, or on clothing. P264 Wash thoroughly after handling. P273 Avoid release to the environment. P281 Use personal protective equipment as required. P404 Store in a closed container. Keep out of reach of children.

Eye contact: Immediately flush eyes with cold water for at least 15 minutes while lifting upper and lower eyelids. Remove contact lenses if present and easy to do without injury, and continue rinsing. If irritation persists, obtain immediate medical attention, preferably from an ophthalmologist.
Skin contact: Wash contaminated skin with plenty of soap and water. Remove contaminated clothing and wash before reuse. If irritation is present or occurs, obtain medical attention.
Inhalation: Move the person to fresh air. If breathing difficulty, signs of overexposure, or illness occur, obtain medical attention.
Ingestion: Do not induce vomiting. If the person is fully conscious, rinse the mouth and give one to two glasses of water to dilute. Obtain immediate medical attention. If vomiting occurs, keep the head below the hips to reduce aspiration risk.
Main symptoms: Eye redness, tearing, pain, burns, or possible corneal injury; skin irritation, redness, drying, burning, or cracking; respiratory irritation from spray mist; and irritation or burning of the mouth, throat, and esophagus with possible nausea, diarrhea, vomiting, and abdominal pain after ingestion.
Aspiration hazard: Not considered an aspiration hazard.

Flammability: Not flammable. Flash point greater than 100°C (212°F), TAG closed cup; NFPA Class III B.
Extinguishing media: Use extinguishing media suitable for the surrounding fire.
Hazardous combustion products: Burning or thermal decomposition can produce carbon monoxide, carbon dioxide, sodium oxides, silicon oxides, and other toxic fumes.
Special protective equipment: Firefighters should use MSHA/NIOSH-approved self-contained breathing apparatus and full protective gear.
Explosion hazards: Static discharge, mechanical impact, and explosion hazards are not applicable.

Warn personnel of the spill and ventilate the area. Avoid slipping on spilled product. Wear safety glasses, chemical-resistant gloves, and rubber boots. Use absorbent socks or pads to prevent spreading. For small spills, recover with a wet vacuum or mop and wringer, then mop the area with clean water. For large spills, absorb with inert material such as dry sand or earth and place in a chemical waste container. Vacuum or sweep remaining material into a suitable disposal container. Prevent unnecessary release to the environment and dispose of recovered material according to applicable regulations.

Handling: Keep away from incompatible materials. Use appropriate safety equipment. Avoid contact with eyes and skin, inhalation of mist, and ingestion. Wash thoroughly after handling and avoid release to the environment.
Storage: Keep out of reach of children. Keep the container tightly closed when not in use. Store below 49°C (120°F) and away from incompatible materials.
Incompatible materials: Strong oxidizing agents and strong acids.

Exposure limit: 2-(2-Butoxyethoxy)ethanol: ACGIH TWA 10 ppm as stated in the source SDS. No exposure limits were established in the source for sodium metasilicate pentahydrate or nonylphenol ethoxylate.
Engineering controls: Provide general ventilation sufficient to keep vapours and mist below applicable exposure limits. If exposure exceeds the threshold limit value, use a MSHA/NIOSH-approved respirator.
Eye protection: Chemical safety glasses, goggles, or face shield.
Hand protection: Impervious chemical-resistant gloves.
Other protection: Eye-wash station and safety shower are recommended. Use appropriate protective clothing where contact may occur.

| Physical state | Liquid |
| Appearance | Clear blue |
| Odour | Peppermint |
| pH | 13.0 (±0.3) |
| Specific gravity / density | 1.08 |
| Flash point | >100°C (212°F), TAG closed cup |
| Solubility | 100% |
| VOC | 0.5% at 5% dilution / 5 mg/L VOC in 5% dilution |
| Molecular weight | Approximately 82.44 g/mol |
| Flammable limits | No data available |
| Auto-ignition temperature | No data available |
| Boiling point | No data available |
| Freezing point | No data available |
| Vapour density | No data available |
| Vapour pressure | No data available |
| Viscosity | No data available |

Reactivity: No specific test data available.
Chemical stability: Stable when stored below 49°C (120°F).
Hazardous polymerization: Will not occur.
Conditions to avoid: Incompatible materials.
Incompatible materials: Strong oxidizing agents and strong acids.
Hazardous decomposition products: Burning or thermal decomposition can produce carbon monoxide, carbon dioxide, sodium oxides, silicon oxides, and other toxic fumes.

Routes of exposure: Eyes, skin, inhalation of mist, and ingestion.
Calculated acute toxicity: Oral 9,247 mg/kg; dermal 16,755 mg/kg; inhalation 57.5 mg/L. The source SDS states these calculated values are outside the applicable acute toxicity categories for the listed routes.
Component acute toxicity: Nonylphenol ethoxylate: oral LD50 rat 960 mg/kg; inhalation LC50 rat 1.15 mg/L over 4 hours (mist); dermal LD50 rabbit 2,991 mg/kg. Sodium metasilicate pentahydrate: oral LD50 rat 847 mg/kg; dermal LD50 rat >5,000 mg/kg. 2-(2-Butoxyethoxy)ethanol: oral LD50 rat 7,291 mg/kg; dermal LD50 rabbit 2,764 mg/kg.
Symptoms: Causes serious eye irritation with redness, tearing, pain, burns, or possible corneal damage. Can cause skin irritation, redness, burning, drying, or cracking. Spray mist may irritate the nose, throat, mucous membranes, or respiratory tract. Ingestion may be harmful and may cause irritation or burning of the mouth, throat, and esophagus, with nausea, diarrhea, vomiting, and abdominal pain.
Target organs: Kidneys and liver.
Carcinogenicity and sensitisation: No data indicating carcinogenicity or sensitisation were provided in the source SDS.

Aquatic toxicity: Nonylphenol ethoxylate: LC50 bluegill 1.0 mg/L (96 hours); EC50 water flea 12.2 mg/L (48 hours). Sodium metasilicate pentahydrate: LC50 zebrafish 210 mg/L (96 hours); EC50 water flea 1,700 mg/L (48 hours). 2-(2-Butoxyethoxy)ethanol: LC50 fish 1,300 mg/L (96 hours); EC50 water flea >100 mg/L (48 hours).
Persistence and degradability: Inherently biodegradable according to the OECD definition.
Bioaccumulative potential: No data available.
Mobility in soil: Water soluble and expected to move readily in soil and water.
Other adverse effects: Harmful to aquatic organisms. Avoid release to the environment.

Dispose of product, absorbents, residues, and contaminated packaging in accordance with applicable local, state, and national regulations. Do not discharge uncontrolled material to drains, surface water, or the environment. No specific waste code was provided in the source SDS.

| UN number | Not regulated |
| Proper shipping name | Non-hazardous compounds, cleaning liquid |
| Transport hazard class | None |
| Packing group | None |
| Label codes | None |
| Marine pollutant | No |
| Additional information | Not regulated as hazardous material for transport according to the source SDS. |

TSCA: Glycol ethers and sodium metasilicate pentahydrate are listed on the Section 8(b) inventory according to the source SDS.
SARA: 2-(2-Butoxyethoxy)ethanol, nonylphenol ethoxylate, and sodium metasilicate pentahydrate are identified as hazardous chemicals with acute and chronic hazards in the source SDS. Glycol ethers are identified for TRI Section 313 emission reporting.
WHMIS: 2-(2-Butoxyethoxy)ethanol is listed on the DSL and classified D-2B, material causing other toxic effects.
International inventories: The source SDS states that glycol ethers are listed in Australia, Canada, Europe (EINECS), Japan, Korea, and the United Kingdom. Users are responsible for confirming current regulatory requirements for their jurisdiction.

Source SDS revision date: 15 February 2024. Supersedes source Safety Data Sheet dated 25 January 2024.
The information contained in this Material Safety Data Sheet has been compiled from sources believed to be reliable and up to date and is accurate to the best of our knowledge. However, no guarantee is made regarding information from other sources or completeness, and no warranty, express or implied, is given. The information is provided for reference purposes to persons with relevant technical skills. Because conditions and methods of use are outside our control, users are responsible for determining safe and suitable conditions of use and assume responsibility for injuries, losses, or damage arising from use of the product or this information. The data relate only to the specific material designated and may not be valid when the material is used in combination with other materials or in another process.