Valvocare Fuel Additive

This is antivanaduim and protect system from SODIUM problem . It is specifically intended to prevent damage of exhaust valve , formulated for treatment and reduction of corrosive deposits formed on exhaust valve seats and turbocharger compone

RXSOL-70-7006-025 is antivanaduim and protect system from SODIUM problem . It is specifically intended to prevent damage of exhaust valve , formulated for treatment and reduction of corrosive deposits formed on exhaust valve seats and turbocharger components.
COMMON NAME : VALV CARE

Application

For physically modifies fuel ash, raising the sinter melting points of the ash above the normal engine operating temperatures. Modified ash particles are solid, small and non-adhesive and are ejected with the exhaust gas steam.

Dose

Typical dose rates vary between 1 : 1000 and 1:5000 ( 1 Ltr / 1-5 MT ) depending on the nature and severity of the problem. For more detail prefer to technical bulletine.

Technical specifications

Note
FUEL ADDITIVE Combustion Improver Catalyst is a flexible way to optimize the use of heavy fuel oils and exhibits the following main properties:
  • Significantly reduces the amount of soot and unburnt hydrocarbons (more than 50%) formed during the combustion of heavy fuel oils
  • Allows reducing the excess air used during the combustion process
  • Improves the flame homogeneity and allows to achieve a more stable yield of combustion
  • Reduces deposits on heat transfer surfaces and consequently allows to achieve a more efficient heat transfer in the convection zone
  • Therefore, reduction in fuel consumption is achieved.
Advantages of Fuel Additive
  • Reduces the unburnt solids by at least 50%
  • Decreases emission of Black smoke & Co. Gas
  • Reduces NOx by at least 30%
  • Satisfies environmental considerations
 
 
Combustion Improver Catalyst must be stored and handled at ambient temperatures not lower than minus 3'C. Carbon Steel, stainless steel, polyethylene, polypropylene or Teflon may be used for construction of storage.
 
The recommended blending method is either by direct injection in the fuel line by a dosing pump or by addition into the fuel storage tank or in the tanker before decantation of the fuel.
 
Combustion Catalyst-cum-Stability Additive:
 
High Performance Multifunctional additive to solve Combustion and Sludge formation problems in fuel oil. Asphaltene + O2 C + CO + CO2 + H2O.
 
Because of the partial combustion, CO and C are not burnt completely. This additive makes the Asphaltenes break down and helps the molecules to burn easily to give more energy. Normally this additive is dosed @ 500 to 750 ppm. Blending should be done in main tanks or storage tanks or tank trucks. This is a blend of performance enhancers, and its functions are given below:
 
Disintegrates the existing sludge molecules into fine Asphaltene molecules.
Avoids formation of sludge and keeps the Asphaltenes in well dispersed state.
Combustion Catalyst breaks down the Asphaltenes into smaller molecules, helps these broken molecules to burn by catalyzing the tough step of carbon monoxide formation, thus improving the heavy fuel oil to burn better, release more heat and as a result, saves fuel.
 
Benefits of Using Fuel Additive Combustion Catalyst:
  • Increases speed of combustion of oil.
  • Accelerates combustion of unburnt hydrocarbons
 
Mechanical:
  • Reduces excess air requirement
  • Reduces heat loss through heat transfer
  • Enhances heat transfer efficiency

Economic Benefits:

  • Effects 3-4% fuel savings, and enhance life of equipment
  • Sludge converts into good oil. Saves time, effort, and labour by avoiding tank cleaning
Environmental Benefits:
  • Reduces smoke, soot and particulate matter in flue gas
  • Reduces NOx by at least 30%; avoids sludge formation and hence sludge handling difficulties.
Combustion Catalyst-cum-Ash Modifier Additive:
 
Added to the function of combustion improver, it reduces deposits in the high temperature zones of the thermic fluid heater / boiler so as to make the thermic fluid heater or the boiler operate on the peak capacity all the times. Avoids corrosion of heat exchanger tubes and premature failure of high temperature surfaces.
Remarks / Precaution

Packing sizes
Specifically intended to prevent damage of exhaust valve , formulated for treatment and reduction of corrosive deposits formed on exhaust valve seats and turbocharger components. Standard Stock available in 20, 25, 50, 210 Ltr packing in Mumbai, Visakhapatnam, Chennai- Ennore, Kolkata, Kandla - Gandhidham, Manglore, Fujairah - Dubai.
MSDS

Product Name RXSOL-70-7006-025
Product Type Valvocare Fuel Additive

Company Details:

RX MARINE INTERNATIONAL
105, A wing , BSEL , TECH PARK.
VASHI ,NEW BOMBAY 400703 INDIA

Stock Point : Mumbai, Kandla, Kolkata, Chennai, Vizag, Fujairah, Muscat

Phone +91 22 65113333 / 5555 / 9999 / 27815540
Fax +91 22 2781 1318 :::AOH :0091 9821214367
Email mail@rxmarine.com
Website www.rxmarine.com

Chemical Name

Concentration

CAS Number

EC Number

R Phrases*

Symbols

Naphtha (petroleum),
Hydrodesulfurized Heavy

30-60

 64742-82-1

 265-185-4 65, 66

Xn

Fatty Alcohol Polyethoxylated Polymer Exemption  1 -20% ......... ......... .......... ......
Manganese Octoate  10 -30% 6535-19-9       

*See Section 16

irritant

Irritant

Odour

Smells of hydrocarbon

Appearance

Liquid, light, yellow

Contact with eyes Causes redness and irritation
Inhalation In cases of severe exposure, anaesthesia may develop, May cause chronic pneumonitis
Classification of the substance or mixture Counsil Directive 1999/45/E EC Classification, packing and labelling of dangerous preparations.
Risk Phrases Harmful: may cause lung damage if swallowed (R65). Repeated exposure may cause skin dryness or cracking (R66)
Safety Phrases Do not breathe spray/mists (S23). Avoid contact with skin (S24).Wear suitable protective clothing, eye/face protection and gloves (S36/37/39) If swallowed, do not induce vomiting: seek medical advice immediately and show this container or label (S62)

Description of first aid measures

Contact with skin

Remove contaminated clothing immediately and drench affected skin with plenty of water. Then wash with soap and water Contaminated clothing should be laundered before reuse. Seek medical attention if irritation persists

Contact with eyes

If substance has got into eyes, immediately wash out with plenty of water for at least 15 minutes.Irrigate eyes thoroughly whilst lifting eyelids When in doubt or symptoms persist, seek medical attention

Ingestion Do not induce vomiting because of risk of aspiration into the lungs. If aspiration is suspected obtain immediate medical attention If vomiting occurs turn patient on side Give water or milk to drink. Obtain immediate medical attention

Inhalation

Remove patient to fresh air. Seek medical attention if ill effects occur

General In case of accident or if you feel unwell, seek medical advice immediately (show the label
where possible) (S45)

Auto-ignition point 220 deg C
Flash point > 62 deg C (CC)
Decomposition products may include carbon oxides, Decomposition products may include carbon dioxide
In case of fire use water spray or fog, alcohol resistant foam, dry chemical or carbon dioxide (S43)
Do not use water jets
Prevent run off water from entering drains if possible
Vapours are heavier than air and may travel considerable distances to a source of ignition and flashback

Personal Precautions

Wear protective clothing as per section 8. Shut off all ignition sources. Vapours are heavier than air and may travel considerable distances to a source of ignition and flashback

Environmental Precautions

Do not allow to enter public sewers and watercourses

Clean Up Actions

Absorb spillage in inert material and shovel up. Ventilate the area and wash spill site after material pick-up is complete

Special Precautions Do not allow to enter public sewers and watercourses. Wear protective clothing as per section 8

Precautions for safe handling
- See Section 8
- Eyewash bottles should be available
- Avoid contact with skin and eyes (S24/25)
- Keep away from heat/sparks/open flames/hot surfaces. - No smoking.

Conditions for safe storage, including any incompatibilities
- Keep only in the original container in a cool, well ventilated place (S3/9/49)
- Keep container tightly closed (S7)
- Keep away from open flames, hot surfaces and sources of ignition.

Control parameters

TLV (TWA) (Naphtha (petroleum), hydrodesulfurized heavy) 275 mg/m3 ( )

Exposure controls

The undiluted product must not be used in a confined space without good ventilation. Ensure adequate ventilation

Occupational exposure controls

Wear suitable protective clothing, including eye/face protection and gloves (neoprene or nitrile are recommended). Wear suitable respiratory protection. Gas cartridge (organic substances). Ensure adequate ventilation

Gloves Suit Goggles Respirator

                                     gloves                      suit                    goggles                       respirator

                                      Gloves                              Suit                           Goggles                     Respirator

Odour

Smells of hydrocarbon

Appearance

Liquid, light, yellow

pH

not applicable

Boiling point

175 °C to 220 °C at 760 mm /Hg

Melting point not known
Density 0,85 g/cm3 at 20 deg C
Flash point > 62 deg C (CC)
Auto-ignition point 220 deg C
Lower explosive limit 0.6 % (in air)
Upper explosive limit 7 % (in air)

- This article is considered stable under normal conditions
- Keep away from naked flames, incandescent or hot surfaces
- See Section 5

Inhalation

Inhalation of solvent vapours may give rise to nausea, headaches and dizziness

Contact with skin

Prolonged skin contact will result in defatting of the skin, leading to irritation, and in some
cases, dermatitis

Contact with eyes

May cause redness and irritation

Ingestion Aspiration hazard. The ingestion of significant quantities may cause damage to lungs

Ecotoxicity This product does not contain ingredients which are classified in the EU as dangerous for the environment. LC50 (fish) 10-100 mg/l (96 hr)

Persistence and degradability

OECD-test. 28 days >60% (Naphta)

Bioaccumulation Potential

Hydrocarbon solvents have the potential to bioaccumilate.

Waste treatment methods

Do not discharge into drains or the environment, dispose to an authorised waste collection point. Disposal should be in accordance with local, state or national legislation

Classification EU Waste class: 07.01. This material and/or its container must be disposed of as hazardous waste

Special precautions for user
- Not classified as hazardous for transport

Classification and labelling Counsil Directive 1999/45/EEC Classification, packing and labelling of dangerous preparations.. This Safety Data Sheet is provided in compliance with TheDangerous Substances Directive (67/548/EEC) Safety, health and environmentalregulations/legislation specific for the substance or mixture. This Safety Data Sheet has been prepared in accordance with article 31 and annex II in REACH and Directive 453/2010/EU.

Text of R and S phrase codes used in this safety data sheet:- R65: Harmful: may cause lung damage if swallowed; R66: Repeated exposure may cause skin dryness or cracking. The information provided about the product on this Safety Data Sheet has been compiled from knowledge of the individual constituents The data given here is based on current knowledge and experience. This Safety Data Sheet describes the product in terms of safety requirements and does not signify any warranty with regard to the product's properties The data given here only applies when product used for proper application(s). The product is not sold as suitable for other applications - usage in such may cause risks not mentioned in this sheet. Do not use for other application(s) without seeking advice from manufacturer

DISCLAIMER OF LIABILITY :The information in this SDS was obtained from sources which we believe are reliable. However, the information is provided without any warranty, express or implied, regarding its correctness. The conditions or methods of handling, storage, use or disposal of the product are beyond our control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of the product. This MSDS was prepared and is to be used only for this product. If the product is used as a component in another product, this MSDS information may not be applicable.
 

Need a quote for this product?

Tell us the grade, packing and quantity you need — we ship across India and to major ports.

Request a quote office@mumbaichemical.com